For all problems, solve for the following a. Vgs b. ld C. Zin d. Zout e. Av 20 V 16.2 ΚΩ 1 MQ HE Ipss-8 mA Vp= -8 V 12.4 ΚΩ

Q: What is the output voltage Vs = 24 /__ 0 ° V0 in the circuit in the figure ?

A:

Q: a) determine the current across R3 b) current across R1 c) voltage and current across R2

A: As per guidelines i have to do first three sub parts.plese post remaining again.

Q: What should the resistors R1, R2, R3 and R4 be so that the gain of the circuit is 2.2

A:

Q: How you will read this graph? How much is the inrush current

A: Inrush Current:- The current that is absorbed by a transformer during transformer energization is…

Q: = Figure Q2 shows the exact equivalent circuit of a 50 Hz, 30 kVA, 2200 V/250 V single- phase…

A:

Q: Q2/ find the 1 ,12 and İr2 for the figure below Rin 1 SV 10 V 2.

A: Apply nodal analysis at node V as shown in the below figure:

Q: what does c3 equal

A: Initial conditions are not given so take, initial conditions = 0.

Q: Calculate the base current for this circuit. +12V 12.5 ka 2 ka silicon Select one: a. 0.904 mA O b.…

A:

Q: iz iT C = R1 R2 + 21

A:

Q: Refer to Figure D. Determine the total current of the entire circuit. a. 1.0 A b. 0.5 A c.   0.2…

A: In this question we will find total current....

Q: QUESTION 10 Find the value of the reelstive component of each loed in this belanced, poithve phese…

A:

Q: Find C/R1 and C/R2 using Mason's rule R₁ G₁ H₂ G₂ H₂+ H₂ G₁

A: “Since you have posted multiple questions with multiple sub parts,we will provide the solution only…

Q: Subject to a step input, the voltage drop across the resistor took 696.3103us to reach 13% of its…

A: for study state , L gets short so  ,i = ViR  ,  V0=Vi As voltage drop across L is 0 at study…

Q: Find the values of Vr, Ic, Ir, C, & Zr. + VR - 35 ohms IR 7V 12V/60HZ Ic +

A: Given: In the given question they have mentioned an AC circuit with having capacitor, resistor and…

Q: In circuit shown in figure, the operating point is chosen such that Ic 1.57 mA, VCE = 3.1V,If Rc =…

A:

Q: 1. Find Ic & UCE if Bac = 200

A: In the given question we need to calculate the Ic and VCE.

Q: Find the DC base current of Q1 (i.e. Ig1) for the following circuit. VBe = 0.7 V (B1 = 64, B2 = 120)…

A:

Q: 5. Refer to Graphic E. What is the voltage across R2? 1.93 V 2.76 V 3.16 V None of the above

A:

Q: The values of determines whether the response is overdamped, underdamped or critically damped a. R,…

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Q: Three resistance 14. 5 Q, 25.5 Q and 60 Q are connected in series across 200 V. What will be the…

A: Given: Three resistances are connected in series, R1=14.5 ΩR2=25.5 ΩR3=60 Ω Supply voltage, Vs = 200…

Q: Draw the Circuit with Multism

A: The circuit can be designed with the multisim and all the parts are available in the multisim…

Q: 17. What is the equivalent resistance of these resistance combinations? R4 R7 R1 R5 12 R2 un RB R6…

A: In this question we need to find a equivalent resistance of the given circuit.

Q: Q-1. Analyze the circuit in Figure 1 to find its output. Q2 T Q T Q T Q Clock Q Q

A: T flip flop  To find the above circuit output Assume initial output be 000.

Q: What is the voltage at the resistor and capacitor?

A:

Q: 23. What is the waveform across D1? halfwave fullwave sinewave DC line 24. What is the waveform…

A: 23. whenever diode conducts then voltage across the diode is constant i.e, for silicon diode it is…

Q: What is the pitch of the thread called out by the thread note illustrated below? 9/16 -9/16-12UNC-2A…

A: Thread note is given it is asked to find the pitch of the thread

Q: Calculate the following. 1. RAE when A&B are connected and E&F are connected 2. RCF when C&D are…

A: As per guidelines i have to solve one .i am solving two . please post remaining again because…

Q: On the second part, you did 60-60 because the charge didn't change. Is that correct?

A: Yes you are correct. The current through capacitor is the ratio of  as change in charge to the…

Q: 1. Find Is. Ic. Ve, , Ve. and VcE for following cireuit (B=100). vcc 20V 500KΩ M Rc 2KN Vo Cin Vin…

A: Given:

Q: for part c what is the actual calculation?

A:

Q: VDD RI Rp Ve out M1 Vin Cp CG RL CG Rs Cs R2 Vss = 0 V SS

A: Types of Biasing in FET Based Amplifier  Fixed DC Biasing  Voltage divider biasing  Self biasing

Q: What's the maximum percent overshoot %OS for this system with its closed-loop poles as shown? jo js…

A: To find the maximum percent overshoot for the given system

Q: V1 M R1 12V 00 D1 R2 00 C2 C1 =1μF =9.4nF U1 -vco RST OUT DIS THR TRI сом GND XSC2 Ext Tig 555 TIMER…

A: PART A: Duty cycle 70% and c1 =94FFrequency 5khz:R1 - 1.23 KohmR2 -0.919 Kohm    Frequency 2KHz:R1 -…

Q: a 3.0 50 b 50.2 4.2 C 1002 20 d e E250 750

A:

Q: What is the percentage accuracy at Vout?

A: For the given potential divider circuit the percentage of accuracy for the output voltage needs to…

Q: HIGH Jo J2 Q, K1 K2 K3 CLK

A: By observing the above circuit it can be concluded that, For JK flip flop the next state can be…

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.