For air, the breakdown voltage for electrodes separated by a distance d is given by the Paschen formula Вра VB In(Apd) – C where A = 15 (torr · cm)- B = 365 V(torr · cm)¯ -1 C ~ 1.53 Note that 760 torr = 1 atm = 101.325 kPa. Electrodes are separated by d = 10 cm in air at pressure p = 760 torr. (a) What is the breakdown voltage? (b) What is the breakdown voltage if the pressure is reduced to p= 700 torr?

For air, the breakdown voltage for electrodes separated by a distance d is given by the Paschen formula Вра VB In(Apd) – C where A = 15 (torr · cm)- B = 365 V(torr · cm)¯ -1 C ~ 1.53 Note that 760 torr = 1 atm = 101.325 kPa. Electrodes are separated by d = 10 cm in air at pressure p = 760 torr. (a) What is the breakdown voltage? (b) What is the breakdown voltage if the pressure is reduced to p= 700 torr?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

ähäi 15 Find the concentration of electrons & holes in (a) N-type Si at 300K, if the conductivity is 300(0.cm)^-1. (b) Also find these values for P-type Si. Given ni=1.5x10^12 /Cm^3, un-1200 *.Cm2/V.sec & pp3400Cm^2/V.sec
Find the concentration of electrons & holes in (a) N-type Si at 300K, if the conductivity is 300(N.cm)^-1. (b) Also find these values for P-type Si. Given ni=1.5x10^12 /Cm^3, un=1200 * .Cm2/V.sec & up=4000m^2/V.sec
Estimate the dielectric losses in the solid specimen subjected to an alternating field of 40KV/cm, has an absolute permittivity of 4.445 x10-11 and the loss angle of that solid dielectric material is 0.28647at Oman power frequency. And also the same specimen while subjected to 3 KV/cm DC supply with the resistance value of 10 Mega Ohm, then determine the heat generated in the specimen.
Consider a semi-conductor bar of uniform dimensions as shown below- A Semiconductor bar B X where x is the length of the semi-conductor equal to 2mm and V is the voltage applied equal to 2 volts. Find out the magnitude of the electric field at the center of the bar.
Graph: Take a graph sheet and divide it into 4 equal parts. Mark origin at the center of the graph sheet. Now mark +ve X-axis as Vf, -ve X-axis as Vr, +ve Y-axis as Ifand –ve Y-axis as Ir. Mark the readings tabulated for Si forward biased condition in first Quadrant and Si reverse biased condition in third Quadrant.
calculate ZL and average Pmax
H.W:- calculate the potential difference from (0,0,10) to (0,0,6) for both cases. Hint: calculate V,at (0,0,6)then find the difference for the tw solution. Activate Winde Go to Settinos to a
2) Vo voltage is applied to the metal parallel plate capacitor system given in the figure. The region between the plates is filled with dielectric material of &-2.4. Bottom plate grounded and d-2mm in the z-axis of the top plate when placed at z=0 are within distance. For tension in the interplate region boundary conditions: If V(z)-0 volts for z-0 and V(z)-Vo volts for z-d; a) Potential expression in the interplate region V=? b) Electric field strength E-? c) Electric flux density D-? d) Surface charge densities of the plates p.=?
10) notation from PHY240, Simplify the following expressions as much as possible. You must use Q = TĀ· (BC )) · (B · (AC ))+ (AB )· (AB · )
A certain conductor bar of rectangular cross section 0.02 by 0.08 m and length 2.0 m has a voltage of 50 mV. If its conductivity is 5.8 x 107 S/m and its mobility is 3.20 x 10-3 m2/V-s, find its volume charge density in giga-C/m3.