For a steady, incompressible two-dimensional flow, represented in Cartesian co- ordinates (x, y), a student correctly writes the equation of pathline of any arbitrary dx dy = ax and by, particle as, 'dt dt where a and b are constants having unit of (second)'. If value of a is 5, determine the value of b.

For a steady, incompressible two-dimensional flow, represented in Cartesian co- ordinates (x, y), a student correctly writes the equation of pathline of any arbitrary dx dy = ax and by, particle as, 'dt dt where a and b are constants having unit of (second)'. If value of a is 5, determine the value of b.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4
Learning Goal: To use the principle of superposition to relate external axial loads on a bar to axial deflections. Under certain conditions, the effect of complicated loads can be calculated by combining the effects of simple component loads. This is called the principle of superposition. This method can only be used when the internal axial force N in a body is linearly related to the displacement or external loading, and the deflections are small enough that the body's geometry does not change significantly. If a complicated load can be expressed as a linear combination of the simpler loads, then the stress or displacement at a point will be the same linear combination of the corresponding responses in the simpler loads. Figure B A 1 of 2 1 KN deflection at point A is deflection at point A is flexibility factor.) Part A Larger load A horizontal bar is attached to a wall. When a force of 1 kN is applied at point A (Figure 1), the AA = 0.47 mm. When a 1 kN force is applied at point B…
c) A thin elastic wire has its both ends tied to two fixed holders and is completely immersed in a flowing fluid. A study is to be carried out to determine the static deflection, 8, at the axis of the wire due to drag that exerted by the flowing fluid. Assume: 8 =f(1, d, p, µ, V, E) where dis a deflection in unit length, I is wire length, d is wire diameter, pis fluid density, u is fluid dynamic viscosity, V is fluid velocity, and E is elastic modulus of the wire. By using Buckingham Pi (t) theorem and basic dimensions system of MLT, predict a suitable set of a Pi (t) terms to study this problem. Use d, p, and V as the repeating variables. The unit of elastic modulus is given as Newton/m?.
Vector O is the resultant of vector M = 9.9i + 3.8j + -3.5k and an unknown vector N. Vector O is a vector in the positive z-direction only and has twice the magnitude of vector M. What is the magnitude of vector N? Express your answers in two decimal places.
b) Uniform streams of fluid cross the boundary of a control volume containing a solid object. Briefly explain how Newton's 2nd and 3rd laws allow the resultant force vector acting on the body to be derived. Figure 2 shows a steady, uniform two-dimensional jet of liquid in the atmosphere impinging on a flat plate inclined at an angle q to the jet axis. The jet cross section area is A, and its velocity is u. The liquid density isr. It is assumed that there are no flow losses, and that all the streamlines end up parallel to the plate. Explain why the resultant force acts perpendicular to the plate, and show that its magnitude is: R22. A.u cosa Figure 2 A
A thin plate with a size of 20 cm x 20 cm, with a constant speed of 1.0 m/S between two walls and F it is drawn in the direction in which it is seen in the figure with its force. The distance between the walls is 3.6 mm, and the wall at the top is fixed, and the wall at the bottom is on the left side it is moving at accurate 0.3 M /s constant speed. Fluid viscosity between walls 0.027 Pa.sn and since the velocity distribution is linear (linear) ; a) draw the speed distribution profile, determine where the speed is "0". b) calculate the "F" force that will pull the plate at a constant speed of 1.0 m/s. Fixed Wall = I mm V= 1 m/s F h2 = 2.6 mmi V. = 0.3 m / s Movable Wall
5.42 Determine by direct integration the centroid of the area shown. Determine by direct integration the centroid of the area shown. Express your answer in terms of a and b.
Also find Nq, hmax,
Fully laminar flow in cylindrical pipe Consider the steady, viscous flow of Newtonian (dynamic viscosity), incompressible(density ρ ) fluid through a pipe with a circular cross-section (radius R) under the constantpressure gradient in the x-directionwhere x1 and x2 are two arbitrary locations along the x-axis, and P1 and P2 are the pressures at those two locations (note that we adopt a modified cylindrical coordinate system here with x instead of z for the axial component, namely, (r, , x)). Coordinates of fluid velocity in the cylindrical coordinates are (ur , u, u). - Show that the velocity field inside the pipe is (0, 0, u) and (photo)- Show that the flow discharge Q is (photo)
Fluid often passes through pores in cell membranes or cell layers. The dimensions are small and the velocities low, so viscous forces dominate (low Reynolds number). Use dimensional analysis, or an approximate method of analysis based on the viscous flow equations, to determine the scaling law that expresses the dependence of the pressure drop across a pore (ΔP) on the flow rate through it (Q). The other parameters that are given include the pore radius, R, and the viscosity of the fluid, μ. The membrane itself should be considered infinitesimally thin so that its thickness does not influence the pressure drop.
Fluid Mechanics
Question 8 In a two-dimensional field the velocity of fluid flow is given by v = (y³ - 5x²y)i + 3Cxy²j. For an incompressible flow, the value of C is: