For a simple piping system of an industrial process and sugar and alcohol, what would be, on average, the appropriate pressure and flow, taking into account that the system has little equipment, such as a heat exchanger?

For a simple piping system of an industrial process and sugar and alcohol, what would be, on average, the appropriate pressure and flow, taking into account that the system has little equipment, such as a heat exchanger?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Note: Show all your solutions in separate sheets as required. Indicate all of your answers on this page in the provided blank lines. 1. Using the Steam Tables, find and entropy of steam at the inlet and outlet of a boiler and heat added when subcooled water at pressure = 5 Mpaa (subcooled by 64 deg C measured at boiler inlet), is superheated to 100 deg C SH at the same pressure. Total flow volume rate of steam = 0.5 cu.m per sec. Indicate units.
Please help me???
In the evaporator of an air conditioning system, air flows over finned tubes through with the refrigerant R134a flows. air out refrigerant in refrigerant out air in The mass flow rate of the air is 0.75 kg/s and the air enters at 40°C and pressure 1.04 bar. The air leaves the evaporator at 25°C and 1.01 bar. The refrigerant enters the evaporator with a quality of 0.2 and a temperature of 12°C. The refrigerant exits as saturated vapor. Obtain the properties of air and R134a using the fluids "Air" and "R134a" in EES. What is the volumetric flow rate of the air entering the heat exchanger (m^3/s)? Determine the rate of heat transfer from the air to the refrigerant (W). Determine the mass flow rate of the refrigerant (kg/s).
Question (1) 1. What are the different methods of the water treatments for boiler make-up water? 2. Determine the power required for a forced draught and induced draught fan in a boiler having coal consumption of 25 komin and airlfuel ratio of 19 by mass. The ambient, air temperature and hot gas temperature at exit are 30 °C and 140 °C respectively. Draught required is equivalent to 32.2 mm of water and mechanical efficiency of motor/fan is merely 70%
... Moving to another question will save this response. Question 7 Compressed air with a flowrate of 8 kg/min flows through a two-stage turbine and heat exchanger system as follows: • At the entrance to the system (point 1), the pressure of the air is 8 bar and the temperature of the air is 359 K. • From 1-2 the air passes through a heat exchanger which increases its temperature to 922 K. • From 2-3 the air passes through a turbine, with a pressure ratio of 3 (i.e. P₂/p₂=3). This first turbine has an isentropic efficiency of 65%. • From 3-4 the air passes through a second heat exchanger, which increases its temperature back up to 922 K. • From 4-5 the air passes through a second turbine with a pressure ratio of 3 and an isentropic efficiency of 80%. The properties of air are: cp = 1.005 kJ/kgk, cv = 0.718 kJ/kgK, R = 0.287 kJ/kgK, and y= 1.4. Select the correct value for each of the following values: ₂) a. The heat transfer to the air in the first heat exchanger (i.e. ₁) i in kW: b.…
IN A THROTTLING VALVE, steam of P = 1000 kPa H = 1000kJ/kg flows until P becomes 100kPa. What is the fraction of the liquid that was vaporized? a.0.118 b.0.189 c.0.159 d.0.140 e.0.258
It's clearly Visible Do not Reject
Thermodynamics 2. Please show me an answer containing the given, required, and Solution for problem Number 1. Your help is much appreciated. Thank you very much
A single-stage single acting air compressor takes air in at 1 bar & delivers at 6.5 bar. Work done by the compressor is 36 kJ and the compressor runs at 150 rpm. Calculate the power required in kW. the power required in kW. Answer
b- An evacuated tank ,shown if fig of 1 ft3 is coupled to air supply line through valve .When the valve is opened, the air flow from supply line at 70°F,120 psi until the pressure reaches 90psi . calculate the final temperature and mass inside tank ,assuming the process is adiabatic. R= 53.34 Ibf-ft/lbm °R use the table below in case. Alr supply line Tank Idcat-Gas Propertiles of Air (English Units)0, Standard Entropy at 1 atm = 161.325 kPa = 14.696 1bf/in.² (R) (Btulbm) (Btu/lbm) (Btu/lbm R) (R) (Btu/lbm) (Btu/lbm) (Btu/Ibm R) 400 68.212 95.634 1.56788 1950 357.243 490.928 1.96404 440 75.047 105.212 1.59071 2000 367.642 504.755 1.97104 480 81.887 114.794 1.61155 2050 378.096 S18.636 1.97790 520 88.733 124.383 1.63074 2100 388.602 532.570 1.98461 536.67 91.589 128.381 1.63831 2150 399.158 546.554 1.99119 540 92.160 129.180 1.63979 2200 409.764 560.588 1.99765 560 95.589 133.980 1.61852 2300 431.114 588.793 2.01018 600 102.457 143.590 1.66510 2400 452.640 617.175 2.02226 1000 172.564…
steam enters the steam generating unit at a pressure of 20 bar and dryness of 0.96 and leaves at the same pressure at a temperature of 350°C. Mass flow rate of steam is 5kg/s. Find the percentage increase in volume (%) due to drying and superheating.
The last 3 parts B,D,E