For a figure shown, a. Draw the influence for reaction at A. b. Draw the influence for Shear At C c. Draw the influence for moment At C. d. Determine the maximum values of these functions for a moving uniform distributed load of 5KN/m. ( Show complete solution.)

Q: The propped cantilever beam shown below has a length of 12 meters and is supported by a roller at A…

A: A propped cantilever beam is given with the following data: Given Data: LengthL=12mModulus of…

Q: Determine the smallest angle theta for equilibrium

A:

Q: Assume a 1.4 tt, 6-8.8 ft, c-17.6ft, w-1200 lbft, and P-2800 lb. By=[ a Determine the vertical…

A: Determine the support reactions Shear at B left  Shear at B right Moment at C Shear at C left Shear…

Q: Forces whose line of action are parallel to each other and are acting in the same direction are…

A: answer is option b.)   explanation is given in below step

Q: A rigid member ACB is shown in the figure. The member is supported at A and B by pinned and guided…

A:

Q: Consider the beam ABCD shown in the figure.

A:

Q: 4) A simply supported box beam is constructed using 4 pieces of 50 x 200 glued together supports the…

A: Size of pieces = 50 × 200 mm

Q: Figure shows a statically determinate beam under distributed loading conditions where C is the…

A:

Q: C A D B 0.25 m 0.5 m 0.15 m

A:

Q: An indeterminate beam carries concentrated loads and a uniformly distributed load as shown in the…

A:

Q: The uniform I-beam has a mass of 54 kg per meter of its length. Determine the tension in the two…

A: Determine the tension in the two supporting cables and the reaction at D..

Q: Using equilibrium i.e. force and moment equilibrium must be sa tisfied for each component, determine…

A: mas od car=1660 kgweight of car=1660*9.81=16284.6 N=16.28 kNcase 1     ∑MA=016.28*5-RB*10=0RB=8.14…

Q: 600 N 500 N.m 400 300 500 20

A:

Q: Question Illustrate the Influence Line and calculate the maximum positive live shear at point C in…

A:

Q: Problem 4 The shown bent tube is connected to a guide at A and rests on a roller support at B. It is…

A:

Q: SITUATION. The tower for a transmission line is modeled by the truss shown. The crossed members in…

A:

Q: For the loaded cantilever beam shown in figure (1). the bending moment distribution along the beam…

A:

Q: For the distributed loads shown (System 1). a) Reduce the distributed loads to three concentrated…

A: The beam must be in equilibrium and for that it has to fulfill conditions which area as follows:…

Q: A. Determine the x and y components of reaction at A. B. Determine the y component of reaction at B.

A: Given: F = 21 kN Free body diagram:

Q: A rectangular beam is supported at both ends. It carries two concentrated load of 30kN, a clockwise…

A: Note - value of reaction is taken as 256.738kN to avoid calculation mistakes.

Q: A symmetrical beam of length 300 mm is loaded with a force of 414 N downwards (positive z) and has…

A: Given: The vertical displacement is given by, wx=FEIyx448-L2x28+L42 The modulus of elasticity is…

Q: The reaction at the roller support in kN.

A:

Q: 2KN/m 3m Problem 1 Figure: Propped Beam

A: Let,R=reaction redudant reaction at roller supportusing double integration method,Consider a x-x…

Q: A 10 m long beam has 2 supports at point A and B. The beam is pinned at Support A and supported by a…

A: soln:Assumptioni Force are transverse due to loadiibeam AB is weightlessiiiForce is acting at centre…

Q: Ql:- The coplanar force system shown in Figure below is subjected to a couple moment (M) and three…

A: From the given system of coplanar forces and moments

Q: URGENT

A:

Q: (20%) Comute the end moments over the spports (10%) Compute the reactions at gthe supports (10%)…

A:

Q: For the propped beam below, determine the magnitude of the redundant reaction at the roller support…

A: To determine the reaction at roller support in propped cantilever beam we have to use deflection due…

Q: The torques shown are exerted on pulleys A and B. Knowing that both shafts are solid, determine the…

A:

Q: P.L B. 6L-

A: a) Free Body Diagram of the given problem:

Influence Lines

The graphs that show the variation of a function at a specific point on a beam or truss due to a unit load placed at any point along the structure are known as influence lines in engineering. Some common functions that are studied with influence lines are shear, moment, and deflection. In designing beams and trusses, it is important to use influence lines in structures where loads would move along their span such as bridges, crane rails, conveyor belts, floor girders, etc. The influence lines help to study where a load will create the maximum effect for any of the functions.