Assume a = 4.4 ft, b = 8.8 ft, c = 17.6 ft, w = 1200 lb/ft, and P = 2800 lb.ByaDy-WBDetermine the vertical reaction forces at B and D.V=Round-off answer to integerDetermine the vertical reaction forcos at D and D.Round-off answer to integerbRound-off answer to integerсIbConstruct the shear force diagram for the beam. Determine the shear force at the following points:x = 4.4 ft. (-) (i.e. just to the left of point B)lbCConstruct the shear force diagram for the beam. Determine the shear force at the following points:x = 4.4 ft. (+) (i.e. just to the right of point B)V=Round-off answer to integerlbConstruct the shear force diagram for the beam. Determine the shear force at the following points:x = 13.2 ft. (-) (i.e. just to the left of point C)Round-off answer to integerlbConstruct the shear force diagram for the beam. Determine the shear force at the following points:M=x = 13.2 ft. (+) (i.e. just to the right of point C)Round-off answer integerConstruct the bending moment diagram for the beam. Determine the bending moment at point CbRound-cft answer to integerlb-ft

Determine the support reactions Shear at B left Shear at B right Moment at C Shear at C left Shear…

Assume a 1.4 tt, 6-8.8 ft, c-17.6ft, w-1200 lbft, and P-2800 lb. By=[ a Determine the vertical reaction forces at B and D. Round-off answer to integer b Round-off answer to integer Determine the vertical reaction forces at D and D. v- lb Round-off answer to integer Ib Construct the shear force diagram for the beam. Determine the shear force at the following points: x 4.4 ft. (-) (i.e. just to the left of point B) OD Construct the shear force diagram for the bearm. Determine the shear force at the following points: x=4.4 tt. (+) (1.0. just to the right of point B) V= Round-off answer to integer b Construct the shear force diagram for the beam. Determine the shear force at the following points: x= 13.2 ft. (-) (l.a. just to the left of point C) Round-off answer to integer Construct the shear force diagram for the beam. Determine the shear force at the following points: M= x-13.2 fl. (+) ( just to the right of poini C) V- Round-off answer intogor Construct the bending moment diagram for the beam. Determine the bending moment al point C Round-cff answer to integer lb-ft

Assume a 1.4 tt, 6-8.8 ft, c-17.6ft, w-1200 lbft, and P-2800 lb. By=[ a Determine the vertical reaction forces at B and D. Round-off answer to integer b Round-off answer to integer Determine the vertical reaction forces at D and D. v- lb Round-off answer to integer Ib Construct the shear force diagram for the beam. Determine the shear force at the following points: x 4.4 ft. (-) (i.e. just to the left of point B) OD Construct the shear force diagram for the bearm. Determine the shear force at the following points: x=4.4 tt. (+) (1.0. just to the right of point B) V= Round-off answer to integer b Construct the shear force diagram for the beam. Determine the shear force at the following points: x= 13.2 ft. (-) (l.a. just to the left of point C) Round-off answer to integer Construct the shear force diagram for the beam. Determine the shear force at the following points: M= x-13.2 fl. (+) ( just to the right of poini C) V- Round-off answer intogor Construct the bending moment diagram for the beam. Determine the bending moment al point C Round-cff answer to integer lb-ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the beam shown, the magnitude of the distributed load is wo = 10.6 kN/m and the beam lengths are a = 6.3 m and b = 18.9 m. (a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the maximum shear force and the maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. Wo В a
For the distributed loads shown (System 1).a) Reduce the distributed loads to three concentrated forces and specify where each force acts along the beam (System 2).b) Reduce the system to an equivalent force and moment at A (System 3).c) How do we know that the simplest resultant exists?d) Draw the simplest resultant (a single force that produces the same moment about A).Note: Draw and label each system.
For a figure shown, a. Draw the influence for reaction at A. b. Draw the influence for Shear At C c. Draw the influence for moment At C. d. Determine the maximum values of these functions for a moving uniform distributed load of 5KN/m. ( Show complete solution.)
For the beam shown below, use your preferred method and determine:a. The reactions at the supports (Ray, Rbx, Rby). b. The shear force diagram. c. The bending moment diagram.
2KH Goo Support reaction at point B=.
Example The beam ABC is loaded via a 500 N.m couple and a 600 N force as shown. ... The beam is connected to the rest of the system by a pin joint at B and a roller support at ... Determine the magnitude of the reaction forces on the beam at the supports.
Show complete solution. Draw the shear and moment diagram.
for the beam shown in the figure, a) find the equation of elastic curve by integration method. b-) Draw (Ty), (mx) oliagrams of the beam. c-) find the suppert reactions. 9=9&N/m 9-9 N/m J L=180cm L=180 cm Figure:
please specify if the results are compression or tension. And please answer both parts.
TYPEWRITTEN ONLY PLEASE FOR UPVOTE. DOWNVOTE FOR HANDWRITTEN. DO NOT ANSWER IF YOU ALREADY ANSWERED THIS. I'LL DOWNVOTE.
please help me with this, thank you
%3D If the intensity of the distributed load acting on the beam is w = 3KN/m, determine the reactions at the roller A and pin B. 3 TA