For a "chair swing ride" design below, the rotating frame is 4-m high. Each chair has a maximum capacity of 80 kg, each has four ropes for stabling and each rope is 3-m long. The max tilt angle is 30 degrees. For any information not listed above, you are free to design it out, for example, no. of chairs, materials, etc (a) Calculate the angular speed to achieve a 30-degree tilt angle? With resumption listed. (b) Design a mechanism that can generate the expected motion, by drawing the mechanism and components of bearing and gears (with dimension).

For a "chair swing ride" design below, the rotating frame is 4-m high. Each chair has a maximum capacity of 80 kg, each has four ropes for stabling and each rope is 3-m long. The max tilt angle is 30 degrees. For any information not listed above, you are free to design it out, for example, no. of chairs, materials, etc (a) Calculate the angular speed to achieve a 30-degree tilt angle? With resumption listed. (b) Design a mechanism that can generate the expected motion, by drawing the mechanism and components of bearing and gears (with dimension).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Hi, I have been given this pin-jointed frame analysis to solve (see pictures of the structure attached). Can you help me? The Figure 2 attached is a simplified structure to undertake a structural analysis on a concept design for a low cost stroller/buggy for children. The buggy consists of a number of metal sections that are pin-jointed together. The buggy is designed to accommodate a child of mass no more than 20 kg, sat on the seat which is supported at four points (Fc) on the frame of the buggy. Assume that the weight of the child is equally distributed across all of the points indicated on Figure 2 as Fc. Assume that there are no additional forces applied to the handle of the buggy, that the buggy is static (stationary) and that the buggy, and the elements of the frame have no mass. At points A and G, there are roll supports. At Points B, F and D there are the pin supports. I am required to determine the following: 1) Draw a free-body diagram of the structure 2) Simplify the Free…
Show the complete solution
solve fast possible as you can
could you help me out by finding solution for this
A solid spare, a solid disk, and a thin hoop are all released from rest at the top of the incline (ho = 20.0 cm). a) without doing any calculations, decide which object would be spinning the fastest when it gets to the bottom. (Explain) b) again, without doing any calculations, decide which object would get to the bottom first. (Which one has greater translational speed?) think CoE. c) assuming all objects are rolling without slipping, have a mass of 2.00 kg and a radius of 3.00 cm, find the rotational and translational speed at the bottom of the incline of any one of these three objects.
a small satellite is 9 by 9 by 12 inches. It's launch mass is 12.25 kg. It's designed to balance Clockwise at a rotational speed of about 0.4 rpm. along the 2-axis. What happens to the spin rate If after 200 day in Space the spin slows to 0.05 rpm, with each spin taking approximately 20 minutes?
The value of Poisson's ratio for steel is between O 0.23 to 0.27 O 0.25 to 0.33 O 0.01 to 0.1
You are sitting in a chair and you are ready to kick a soccer ball from a sitting position using only your quadriceps muscles to rotate your knee. Be sure you will not pivot your hips, as you are sitting in the chair; we want to simplify this problem to include only rotating your lower leg at the knee joint and keeping your thigh firmly fixed to the seat. For our purposes, your quadriceps muscles can be treated as a single string that exerts a tension on the knee at a right angle from a lever arm of 2.00 cm. The knee is connected to a plausible 50.0 cm lower leg as measured from the pivot point of the knee to the contact point where we will kick the ball.Before we kick it, we would like to balance the ball on our contact point (at our ankle, say) 50.0 cm away from the pivot point of the knee by extending the lower leg straight out (upper leg aligned with the lower leg). The soccer ball has a mass of 400 grams. We will neglect all mass of all parts of the leg here for brevity c) We now…
Both portions of the rod ABC are made of an aluminum for which E = 69.9GPA. Knowing that the magnitude of Q is 32314 N, m = 0.37 m, and n = 0.54 m, determine the value of P (in N) so that the deflection at A is zero. Express your answer in four decimal places. ... A 20-mm diameter 60-mm diameter
A professor's office door is 0.99 m wide, 2.2 m high, 4.2 cm thick; has a mass of 27 kg, and pivots on frictionless hinges. A "door closer" is attached to door and the top of the door frame. When the door is open and at rest, the door closer exerts a torque of 5.6 N*m. What is the moment of inertia of the door? If you let go of the open door, what is its angular acceleration immediately afterward?