For a certain interval of motion the pin A is forced to move in the fixed parabolic slot by the horizontal slotted arm which is elevated in the y-direction at the constant rate of 5.0 in./sec. All measurements are in inches and seconds. Calculate the velocity v and acceleration a of pin A when x = 4.0 in. Answers: What are the components of the velocity and acceleration of pin A in the y-direction when x = 4.0 in.? Vy= ay = IN x = y²/7 i A in./sec in./sec²

For a certain interval of motion the pin A is forced to move in the fixed parabolic slot by the horizontal slotted arm which is elevated in the y-direction at the constant rate of 5.0 in./sec. All measurements are in inches and seconds. Calculate the velocity v and acceleration a of pin A when x = 4.0 in. Answers: What are the components of the velocity and acceleration of pin A in the y-direction when x = 4.0 in.? Vy= ay = IN x = y²/7 i A in./sec in./sec²

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

reply asapp!! Given a cantilever beam with given loadings and cross-section as shown in the figures, what is the first moment of area (statical moment of area), Q, of the diamond cross- section at the neutral axis? (in mm3) Write the answer in ordinary notation (e.g. 2100000.65) NOT in scientific notation.
A pipe intersection has moments on 3 of its branches as depicted in the figure and parameter table. Calculate the resultant moment and express as a Cartesian vector. 080 BY NO SA 2021 Cathy Zupke X M₁ L₁ L2 parameter value units 1 ft 4 ft 3 ft 2.5 ft ft L3 LA L5 M₁ M₂ M3 200 Z The resultant moment is M3 200 lb-ft 250 lb.ft lb-ft NOTE: Use i, j, k for î, j, k M₂ L5 lb-ft
can you answer the question
The 28000-1b airplane is flying in the vertical plane at 390 ft/s. At the instant shown, the angle = 30°, and the cartesian components of the plane's acceleration are a = -5 ft/s², ay = 25 ft/s². Figure < 1 of 1 Part A What are the tangential and normal components of the total force acting on the airplane (including its weight)? Enter your answers numerically separated by a comma. Ft, Fn = Submit Part B * Incorrect; Try Again; 4 attempts remaining ■AΣ vec de/dt = Previous Answers Request Answer What is de/dt in degrees per second? (Figure 1) Submit VAZ † vec Request Answer ? ? lb °/s
A 200-lb block is sliding along a horizontal plane at 4 ft/s when a force P is applied on it as shown. The magnitude of P varies according to the relation P = 200t lb where t is in sec. Find the velocity of the block 2 sec after P is applied. Neglect friction. Use Impulse-Momentum Method and draw the momenta and impulse vectors.
i=1 error in diagram,left is a pin, right is roller draw the shear and moment diagrams
Given a cantilever beam with given loadings and cross-section as shown in the figures, what is the first moment of area, Q, of the diamond cross-section at the neutral axis? (in mm) Write the answer in ordinary notation (e.g. 2100000.65) NOT in scientific notation. 70KN 40 tNm 600 mm 15KN/m GOomm 600 mm GOomm
1
In (Figure 1), F = {80i + 96j + 48k} lb. Figure 1 ft -2 ft 3 ft 45° B 1 of 1 Part A Determine the magnitude of the moment of F about point A. Express your answer in pound-feet to three significant figures. 15] ΑΣΦ11 MA = Submit Part B α, B, y = Submit Request Answer Provide Feedback Determine the coordinate direction angles of the moment of F about point A. Express your answers in degrees to three significant figures separated by commas. vec U/ ΨΕ ΑΣΦ ↓↑ vec Request Answer ? lb. ft ? Next >
15 N/cm? 9.00 m |2.00 m O 100 mm lo.00 m 25 Calculate the force on the elbow in the system shown in the figure.
28
Determine the deflection @C using Moment Area Method. (Your final answer should be in "mm") 10 kN/m 4 kN A C D B 7 т 3 т 4 т E = 200 GPa I = 140 x 106 mm* Note: Express your answer in two decimal places. No need to type the units.