For a cantilevered beam attached on the left side and subject to a downward force P at its right end (a distance of L from the right end), draw a FBD of the left half and the right half. Include internal moment, shear, and normal forces. Draw the shear and moment diagrams.How are loading, shear, and moment related? Write equations that relate these quantities.

For a cantilevered beam attached on the left side and subject to a downward force P at its right end (a distance of L from the right end), draw a FBD of the left half and the right half. Include internal moment, shear, and normal forces. Draw the shear and moment diagrams.How are loading, shear, and moment related? Write equations that relate these quantities.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Three chains act on the bracket such that they create a resultant force having a magnitude of 500 lb. If two of the chains are subjected to known forces, as shown, determine the angle of the third chain measured clockwise from the positive x axis, so that the magnitude of force F in this chain is a minimum. All forces lie in the x–y plane. What is the magnitude of F? Hint: First find the resultant of the two known forces. Force F acts in this direction. show the formula and the exact solution.
2.F6 A container of mass m = 120 kg is supported by three cables as shown. Draw the free- body diagram needed to determine the tension in each cable. 360 mm 500 mm Z D y A B 450 mm 600 mm 320 mm X
OEVALUATE The following problems are given to assess your ability to solve problems on equilibrium of force systems. Instructions. Solve the following problems, refer to your Assignment Guide on the specific guidelines on formats and how to submit your solution. 1. The beam is subjected to a load F = 400 N and is supported by the rope and the smooth surfaces at A and B. B a. Draw the free-body diagram of the beam. 45 30° b. What are the magnitudes of the reactions at A and B? -1.2 m-1.5 m-1m- 2. For the beam shown: a. Draw the free-body diagram of 1.8 m 1.8 m 1.38 kN the beam. b. Determine the reactions at the supports. 0.80 kN 25 AL 1.5r 1.5m 21m m, 3. Three cables are joined at the junction ring C. Determine the tensions in cables AC and caused by the weight of the 30-kg cylinder. 45 15° 30 kg 30%
For the beam shown, the magnitude of the concentrated load is P = 27 kN, the magnitude of the couple is MB = 170 kN·m, and the beam lengths are a = 6.4 m and b = 19.2 m. (a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the magnitudes of the maximum shear force and the maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
For the beam shown, the magnitude of the concentrated load is P = 23 kN, the magnitude of the couple is MB = 350 kN·m, and the beam lengths are a = 7.2 m and b = 21.6 m.(a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A.(b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the magnitudes of the maximum shear force and the maximum bending moment.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. Part 1 Cut a cross-section through the beam at variable distance x, where 0 < x < a. Derive equations for the shear force V and…
For the beam shown, the magnitude of the concentrated load is P = 28 kN, the magnitude of the couple is MB = 230 kN·m, and the beam lengths are a = 5.8 m and b = 17.4 m. (a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the magnitudes of the maximum shear force and the maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
What is the BENDING MOMENT AT A? (Use 2 decimal places and refer to the question and solutions above.)
For the beam shown, the magnitude of the concentrated load is P = 12 kN, the magnitude of the couple is MB = 150 kN·m, and the beam lengths are a = 4.7 m and b = 14.1 m. (a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the magnitudes of the maximum shear force and the maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Determine the values of F and P, if possible so that the force system shown in cases (b) through (d) are equivalent to the force system shown in case (a). F and P must maintain their direction as drawn. This is a problem where explanations will be critical to explain the logic you used. 12 kip |F 8 ft 4 kip 4 ft 4 ft 4 ft 4ft 4 ft 4 ft (a) (b) 2 kip 2 kip 2 kip (c) (d)
This is one question that has 3 parts to it. Solve parts a, b and c.