Following is the given data of compressive strength test done on 2 inch cement mortar cubes: Maximum Load (lb) 17640 18270 17890 16350 16740 15990 14870 15260 15790 w/c Cube No. Ratio 0.50 2 0.55 0.60 Determine: a) Compressive strength of each cube. b) Average compressive strength for each mix.

Following is the given data of compressive strength test done on 2 inch cement mortar cubes: Maximum Load (lb) 17640 18270 17890 16350 16740 15990 14870 15260 15790 w/c Cube No. Ratio 0.50 2 0.55 0.60 Determine: a) Compressive strength of each cube. b) Average compressive strength for each mix.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: To test the compressive strength of cement mortar, three 2” cubes were cast with three different…

A: Given: Length of mortar cubes = 2 in Mix No. w/c Ratio Cube No. Maximum Load (lb) 1…

Q: y consider the following data for concrete with mild exposure, calculate the quantity of cemer…

A: Given:Volume of water=191.6 litreWater cement ratio=0.5

Q: a) Calculate the temperature of aggregates to produce fresh concrete having the same temperature…

A: Given data, Weight of aggregates (Wa) = 1840 kg Weight of Cement (Wc) = 330 kg Weight of water…

Q: The specified 28-day compressive strength of concrete for a project is fc’ = 36MPa. This statistical…

Q: .The characteristic compressive strength of concrete required in a project is 25 MPa and standard…

Q: The characteristic compressive strength of concrete required in a project is 25 MPa and the standard…

A: Given- fck=25 MPa,standard deviation σ=4 MPa, It is needed to find the water cement ratio.

Q: The following table represents a concrete mixture that has not been completely proportioned. The…

A: Question is based on the concrete mixture (oven dry basis) . Proportion of water, Air, coarse…

Q: Q-5, In a concrete mix of proportion 1:3:6, find the actual quantity of sand, which is judged to…

A: Given- Concrete mix proportion- 1:3:6, Bulking =15 %, It is needed to find the actual volume of the…

Q: The following mix design information is provided to you for 1 m³ concrete. • Air content = 5% • w/cm…

A: Reference : Concrete technology, Mix design ACI 318 mix design code Given : Air content, w/c ratio,…

Q: The water-cement ratio (in percent, round off to the lower integer) to be used in the mix

A: Given data, Characteristic Compressive strength C=25 MPaObserved compressive strength,σ=4 MPaRatio…

Q: What is the amount of cement in kilograms needed for the design mix? (use two decimal places, no…

A: Answer To calculate the amount of cement in kilogram needed for the design mix we need to obtain…

Q: . Determine the compressive strength of each cylinder after 7 days. b. Determine the average…

Q: In a ready-mix plant, cylindrical samples are prepared and tested periodically to detect any mix…

Q: Mixing and handling can significantly alter the air content of fresh concrete. Thus, field tests are…

A: Air entrapped concrete is used generally in areas with low temperatures and damages can occur due to…

Q: Fineness of cement is measured in the units of (a) volume/mass (c) area/mass (b) mass/volume (d)…

A: Fineness of generally indicate the particle size . It measured in the unit of area/mass

Q: How does shape and surface texture of aggregate effect workability, water requirement, and bond in…

A: Concrete is a combination of cement, aggregate, as well as liquid. Aggregate, typically makes up 60…

Q: In proportioning a concrete mix, the coarse and fine aggregates had the following properties…

A: Coarse aggregate weight = 800 lbDry aggregate weight = 350 lb

Q: 1. Following data are given for designing a Portland cement concrete mix for a nonstructural…

A: Note:- Hi, thank you for the question. As per our Honor code, we are allowed to attempt the first…

Q: Sieve Size Amount Retained, Ib 3 in. 2 in. 1-1/2 in. 3.7 1 in. 15.9 3/4 in. 12.0 1/2 in. 13.5 3/8…

Q: A concrete mix consists of 5 gallons of water for each bag of cement. What is the expected…

A: To find the strength of the concrete depending on the values given. 5 gallons of water per each bag…

Q: Question-6 b The gel-space ratio of a concrete sample is given as 0.6. What is the theoretical…

A: Given data- Gel-space ratio X=0.6, To Find- The theoretical strength of the sample.

Q: A materials engineer is working in a research project to evaluate the effect of one type of…

A: The concrete design needs to be like individual codes defining the terms of a complete building…

Q: Design a concrete mix according to the following conditions: Design Specifications Concrete…

A: All the design calculations and specifications are based on ASCE codes. For 50mm slump and 37.5mm…

Q: The characteristic compressive strength of concrete required is a project is 25 MPa and standard…

A: Given data- Characteristic compressive strength of concrete = 25 MPa, Standard deviation = 4 MPa,…

Q: The recommended dosage on a viscosity modifying admixture is 5 fl oz/cwt. The proportions of the…

A: Recommended dosage on a viscosity modifying admixture = 5 fl oz/cwt. Coarse aggregate = 1800 lbFine…

Q: Concrete was mixed with the following ingredients: 50 kg of cement, 100 kg of sand, 150 kg of…

Q: Create a design mix using the ACI DESIGN MIX PROCEDURE with the following parameters: Non-air…

A: Answer Based on the given data we can use below table from ACI 211.1 to obtain the amount of…

Q: The following table provides data obtained during a specific gravity and absorption test on coarse…

A: The mass of oven-dry sample in the air (g), A = 2998.4The mass of the SSD sample in the air (g), B =…

Q: compute for the corrected amount of water needed in the concrete mix if the mass and fine coarse…

Q: A sieve analysis test was performed on a sample of coarse aggregate and produced the following…

A: Sieve analysis test was performed on a sample of coarse aggregate. We need to determine the closest…

Q: Sieve Size Amount Retained, Ib 3 in. 2 in. 1-1/2 in. 3.7 1 in. 15.9 3/4 in. 12.0 1/2 in. 13.5 3/8…

A: Given Sieve Analysis table Typical range of fineness modulus of sand

Concept explainers

Types of Cement

Cement is a fine mixture of limestone, chalk, or marl and clay which when mixed with water, becomes compacted due to the formation of strong molecular bonds. Due to hydration, cement turns into a hard mass when left for a sufficient amount of time upon mixing with water. The water turns the cement compounds into gel-like submicroscopic particles having higher surface areas. It is due to the hydration properties of cement, they are often known as hydraulic cement. For instance, Portland cement is a popular example in this category.

Question

Following is the given data of compressive
strength test done on 2 inch cement mortar
cubes:
w/c
Cube
Maximum Load
(lb)
17640
18270
17890
16350
16740
15990
14870
15260
15790
Ratio
No.
0.50
0.55
2
0.60
Determine:
a) Compressive strength of each cube.
b) Average compressive strength for each mix.
312m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Based from the proportion that you have designed, say that the concrete is mixed to fill 20 cubes (100 x 100 x 100mm) and 10 prisms (500 x 100 x 100mm), find the mass of each material based on the aggregate conditions in Table 2.
Use metric please
Note:hand written solution should be avoided.
Find the quantity of cement.
Discuss and conclude Surface Hardness Test On Concrete
Two batches of concrete cylinders were made with and without a calcium chloride (CaCl2) accelerator admixture. Six cylinders were made of each batch and submerged in water for different times before testing for compressive strength and the results are shown in Table P6.34. It is required to do the following: a. Using an Excel sheet, plot the relationship between curing time and compressive strength of the two mixes on the same graph. Label all axes and curves. b. Comment on the effect of the accelerator on the compressive strength of PCC at early and late ages. TABLE P6.34 Cylinder no. 1 2 3 4 5 6 Water submergence (days) Compressive strength of plain concrete (MPa) Compressive strength of concrete with accelerator (MPa) 1 3 7 14 21 28 0.8 7.8 15.8 21.1 24.5 26.8 6.2 14.8 20.1 24.0 25.9 26.8
In a ready-mix plant, cylindrical samples are prepared and tested periodically to detect any mix problem and to ensure that the compressive strength is higher than the lower specification limit. The minimum target value was at 42.0 MPa. The following compressive strength data were collected: All in Mega-Pascal (MPa) 41.8, 38.3, 42.5, 39.6, 42.5, 39.3, 41.2, 40.9, 39.8, 41.6 42.9, 43.4, 39.9, 44.7, 45.1, 43.9, 42.4, 41.7, 41.1, 42.1 Calculate the Arithmetic Mean, Median, and Standard Deviation. (Non-anonymous question@) .
Do not use chatgpt and provide answer in theoreticall parts
Concrete Technical / Practical Part.
Working on major construction project that requires considerable amounts of concrete to be used,you are asked to design a concrete mix following the BRE methodology. The concrete mixspecifications are:o Characteristic compressive strength of 50 N/mm 2 at 7 days.o Failure rate of 2%o Previous control data yielded a standard deviation of 5 N/mm 2o CEM-I 52.5o Air-entraining is not requiredo Required slump 120 mmo Coarse aggregate: Crushed maximum size 10mmo Fine aggregate: Uncrushed with 45% passing 600 μm sieveo Relative density of aggregates: 2.7o Coarse aggregate has 4% moistureo Fine aggregate is dry and has 1.2% absorption.o Volume of the required trial mix: 0.120 m3 Create the mix design and state what actions and recommenations you would do if trial produced a result with a mean compressive strength of 64 MPa at 7 days and the slump was 80mm.
Q3: Discuss importance of sieve analysis test conducted on both fine and coarse aggregateQ4: Concrete cylinder placed in universal testing is subject to axial compressive load. Concretecylinder crushed at a load of 85 kilo pounds, calculate compressive strength of concrete. (Concretecylinder has 6 inches diameter and 12 inches height)