Flange width is 2in, Front Spar Flange Thickness is 0.30in, Rear Spar Flange width is lin, Rear Spar Flange thickness is 0.20in. Shear Modulus is 11x10^6 psi and length of the cell structure is 50in. The applied shear force is 6000lb and torque is 8000 ft.lb. For question No.1, what is the total enclosed area of the cell structure? * Right Triangular Section 18in Rectangular Section 6in Right Triangular Section 6in D= 18in

Flange width is 2in, Front Spar Flange Thickness is 0.30in, Rear Spar Flange width is lin, Rear Spar Flange thickness is 0.20in. Shear Modulus is 11x10^6 psi and length of the cell structure is 50in. The applied shear force is 6000lb and torque is 8000 ft.lb. For question No.1, what is the total enclosed area of the cell structure? * Right Triangular Section 18in Rectangular Section 6in Right Triangular Section 6in D= 18in

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find the diameter of dAB dec bar if the stress equal to 0.15GPA C 120cm B 125kN 125KN 90cm A 60kN
find the maximum tensile and compressive bending stress make P= 4p x 12= 48KN P= 5P x 12= 60KN W= 9kN/m M= 50 kN.m. note: dimensions are in mm
Design the shear reinforcement for the beam shown in figure below assuming it resists an ultimate shear force at distance d from the face of the support of 450 kN. The characteristic material strengths are fok= 25 N/mm²and fm = 500 N/mm² 450 kN d= 500 mm -4H25 b= 300 mm
P 130 mm 25 mm 25 mm P P 3. Assume that the axial load P applied to the lap joint is distributed equally among the three 20-mm-diameter rivets. What is the maximum load P that can be applied if the allowable stresses are 40 MPa for shear in rivets, 90 MPa for bearing between a plate and a rivet, and 120 MPa for tension in the plates?
Activity 3 Questions WHAT'S YOUR SCORE? Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 15 mm. Determine the largest allowable value of P if the shear stress in the shaft is not to exceed 120 MPa and its angle of twist is limited to 5º. Use G = 80 GPa for steel. (Note: Two values of P are to be compared here). 300 mm 500 mm
Three plates are welded together to form the section shown. Dimensions of the cross section are b= 4.7 in., d = 14.1 in., a = 2.8 in., and t= 0.5 in. For a vertical shear force of V = 42 kips, determine the shear flow through the welded surface at B. B a b Answer: kip/in.
PROBLEM 3 340 mm The plates are connected by 9-20 mm bolts. Force F = 5Ở KN are applied at both plates in opposite directions as shown in Figure 3. Compute the following: A. Axial stress of each plate. B. Shear stress of each bolt. Assume that each bolt resists the applied force equally. %3D +F 150 mm 中 F 50 mm 340 mm Figure 3: Bolted Plates
4.15 Knowing that for the casting shown in the figure the allowable stress is 6 ksi in tension and 15 ksi in compression, determine the maximum couple M that can be applied.
A3-m long steel plate having a cross-section of 25 mm x 300 mm is used as a hanger and subjected to a tensile load of 1070 KN. Poisson's Ratio = 0.25 and E = 200 000 MPa. Compute the total lateral deformation in mm (along the 300 mm side). Express your answers in 4 decimal places.
6.59 A square section as shown in the figure below is subjected to bending moment M. (c) Obc = Obl y || h y H What is the maximum bending stress? (a) Obc = obt 12M h³ 9M 2h³ JXC h (b) bc = Obt = (d) %bc =%bt = 6M 4³ 9M h³
Determine modulus of elasticity