Five different particle sizes are mixed in proportions shown below and water is added to make the volume of soil suspension exactly equal to 1000 cc. Particle size, mm Weight, g 0.060 0.020 0.010 0.005 0.001 5 15 20 4 6 The particles have a specific gravity of 2.65 and the dynamic viscosity of water is 8.95 millipoises. Y can be taken as 1.0 g/cc. The soil suspension was thoroughly shaken and sedimentation allowed. What is the largest particle size present at a depth of 10 cm after 8 minutes of the start of sedimentation? What is the specific gravity of the soil suspension at a depth of 10cm after 8 minutes of the start of sedimentation?

Five different particle sizes are mixed in proportions shown below and water is added to make the volume of soil suspension exactly equal to 1000 cc. Particle size, mm Weight, g 0.060 0.020 0.010 0.005 0.001 5 15 20 4 6 The particles have a specific gravity of 2.65 and the dynamic viscosity of water is 8.95 millipoises. Y can be taken as 1.0 g/cc. The soil suspension was thoroughly shaken and sedimentation allowed. What is the largest particle size present at a depth of 10 cm after 8 minutes of the start of sedimentation? What is the specific gravity of the soil suspension at a depth of 10cm after 8 minutes of the start of sedimentation?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

You have 1 mL (total volume) sample of quartz spheres, and it has a mass of 2.00g . What is the Void Ratio, using only the above information? Void Ratio: e = Vv /Vs Vv= volume of voids Vs = volume of solids
Sieve analysis of a sample of fine aggregate resulted in the following data No. Sieve number 4 8 16 30 50 100 Sieve opening (mm) 4.75 2.36 1.18 0.6 0.3 0.15 Weight retained (g) 13 75 120 126 105 61 A) The total weight of the sample, assuming no mass loss during the analysis, is______ (g) a) 505; b) 500; c) 550 B) The half sieve used in the experiment is________. a) No.8; b) No.50; c) none of the above C) The fineness modulus of the aggregate________. a) 6.13; b) 3.16; c) 1.36 D) The average size of the aggregate___________. a) No.30; b) No.4; c) No.16
i need the answer quickly
Subject soil Mechanics
Q3. A 1200 g sample of Gravel in the SSD condition in air and weighed 770 g when immersed in water. Also, a 500 g sample of Sand in the SSD condition in air and weighed 300 g when immersed in water Calculate the BSG(SSD) of the sand and gravel 1) the BSG (SSD) of the Gravel * 1.2.791 2.4.71 3.3.703 4.2.50 2) the BSG (SSD) of the Sand * 1.2.221 2.3.590 3.2.500 4.3.232 Choose one answer and write the answer number for me
Make comments about the general properties of the soil by classifying the floors given in the figures in the laboratory test results according to AASHTO and UCSC.
A) compare by drawing between the Clay minerals of 1/1 and clay minerals of 1/2
The figure and the table below, shows the results of consolidation test for a soil sample, Find the cc value. TI Applied pressure, kPa 25 50 100 200 400 800 Voids ratio 0.634 0.619 0.583 0.523 0456 0383 0.65 0.6 0.55 0.5 0.45 0.4 of 0.35 10 100 1000 PRESSURE 0.15 0.21 0.12 no one 0.30 VOIDS RATIO
determine the effective specific gravity of aggregates. DATA: Specific Gravity: Fine Agg = 2.603 Coarse Agg = 2.740 Asphalt Cement = 1.048 Percent By Weight: Fine Agg = 47.90 Coarse Agg= 47.78 Asphalt Cement= 100-FA-CA
Given a compacted aggregates with a size of 2”, given the mass of aggregate plus measure equivalent to 10500g, mass of the measure is 350g and the factor of the measure is equivalent to 290 /cu. m. Calculate the Bulk density of the Sample? a 3500.0 kg/m3 b 2943.5 kg/m3 c 2903.5 kg/m3 d 3270.7 kg/m3
Question 4 Comment the four types of sieve analysis diagrams, which appear in the figure below: Continuum, Uniform, Gaps, Open. % Passing 100 O Continuum A Gaps Sieve size Open Uniform
SITUATION 3. Following are the results of a sieve analysis. SIEVE NO. OPENING (mm) RETAINED 4 4.75 10 2.0 40 20 0.85 60 40 0.425 89 60 0.25 140 80 0.18 122 100 0.15 210 200 0.075 56 PAN 12 a. Find the effective particle size. b. Determine the uniformity coefficient. c. Find the coefficient of curvature.