Cummulative Percent SIEVE ANALYSIS GRAPH Weight Retained (g) Retained (%) Sieve Size Percent Percent Passing (mm) Retained (%) (%) 100 4.75 238 47.6 47.6 52.4 90 80 2.36 209 41.8 89.4 10.6 70 2.00 19 3.8 93.2 6.8 60 1.80 13 2.6 95.8 4.2 50 21 4.2 100.0 0.0 40 Series1 - 500 100 30 20 10 Sieve Size Percent (mm) Passing (%) 5.00 4.00 3.00 2.00 1.00 0.00 4.75 52 Sieve Size (mm) 2.36 11 2.00 1.80 Pan Percent Passing (%)

Cummulative Percent SIEVE ANALYSIS GRAPH Weight Retained (g) Retained (%) Sieve Size Percent Percent Passing (mm) Retained (%) (%) 100 4.75 238 47.6 47.6 52.4 90 80 2.36 209 41.8 89.4 10.6 70 2.00 19 3.8 93.2 6.8 60 1.80 13 2.6 95.8 4.2 50 21 4.2 100.0 0.0 40 Series1 - 500 100 30 20 10 Sieve Size Percent (mm) Passing (%) 5.00 4.00 3.00 2.00 1.00 0.00 4.75 52 Sieve Size (mm) 2.36 11 2.00 1.80 Pan Percent Passing (%)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Distinguish porosity from voids content for aggregate with the help of schematic diagrams.
formed? Q1: B: The specific gravity and absorption test was performed on fine aggregate and the following data were obtained: Mass of SSD sand = 500.0 g Mass of pycnometer with water only = 623.0 g Mass of pycnometer with sand and water= 938.2 g Mass of dry sand = 495.5 g Calculate the specific gravity values (dry bulk, SSD, and apparent) and the absorption of the fine aggregate.
Three samples of fine aggregate were taken from the same stockpile and have the properties shown below. Determine in percentage: (a) total moisture content of each sample, (b) free moisture content of each sample, and (c) the average values of each from the stockpile. Measure Wet Mass (g) Dry Mass (g) Absorption (%) A 521.0 491.6 2.5 Sample B 522.4 491.7 2.4 C 523.4 492.1 2.3
If the specimen is originally square and has dimensions of a = 4 in., b = 3 in., and a thickness of t = 0.4 in., determine its new dimension a' after the load is applied. Express your answer to six significant figures and include appropriate units. a' = 4.00737 μA Submit Previous Answers Request Answer Part B X Incorrect; Try Again; 5 attempts remaining 0 in Determine its new dimension b' after the load is applied. Express your answer to six significant figures and include appropriate units. μᾶ b= 3.00333 ? in Submit Previous Answers Request Answer ? X Incorrect; Try Again; 5 attempts remaining
3 - What a hardness test can show. What kind of test can hardness test replace?
To determine the particle size distribution of fine and coarse aggregate by dry sieving.
In a ready-mix plant, cylindrical samples are prepared and tested periodically to detect any mix problem and to ensure that the compressive strength is higher than the lower specification limit. The minimum target value was set at 27.6 MPa. The compressive strength data shown in Table P7.48 were collected. Use one system of units only as specified by the instructor. a. Calculate the mean, standard deviation, and the coefficient of variation of the data.b. Using a spreadsheet program, create a control chart for these data showing the target value and the lower specification limit. Is the plant production meeting the specification requirement? If not, comment on possible reasons. Comment on the data scatter.
Explain how 27Al NMR is useful for studying cement hydration.
Standard Test Method for Ductility of Bituminous Materials 7) What is the effect of improper level of briquette placement ?8) What is the effect of rate of pulling on ductility value ?9) What is the effect of dimensions of the briquette on ductility value
Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced the following results: a. Calculate the percent passing through each sieve. b. Plot the percent finer in a semi-log gradation chart. c. What is the maximum aggregate size of the sample? d. What is the nominal maximum aggregate size of the sample? e. What is the fineness modulus? Is it in typical range? " Sieve Size, 9.5 4.75 3.35 2.36 2.00 1.18 0.85 0.60 0.425 0.30 0.25 0.18 0.15 (No. 0.075 Pan mm (in) (3/8) (No. 4) (No. 6) (No. 8) (No. 10) (No. 16) (No. 20) (No. 30) (No. 40) (No. 50) (No. 60) (No. 80) 100) (No. 200)| Amount 25 59 75 86 115 136 169 192 225 198 173 112 90 33 12 Datained.
Why is it necessary to dry aggregates prior to sieve analysis?