Find the y-coordinate of the center of mass of this object (do not find the x coordinate of the center of mass 1 Sydm Y cm

Q: tarting at rest, a hydroplane accelerates at a = 0.8t for the first 10 seconds and then accelerates…

A: Given:The acceleration is The acceleration after  is

Q: Determine the minimum weight W to prevent downplane motion of the 1000 lb body. The coefficient of…

A:

Q: The maximum possible (Carnot) efficiency of a heat engine operating between constant temperature…

A:

Q: The figure below shows the S-N curve of three materials subjected to cyclic fatigue about a mean…

A:

Q: How is the tool geometry of single point cutting tool designated or specified in ASA, ORS and NRS…

A: GIVEN DATA - TOOL DESIGNATION SYSTEM GIVEN WE HAVE TO EXPLAIN IT

Q: The velocity of a particle moving in the x-y plane is given by (7.82i +3.51j) m/s at time t = 3.15…

A: Given:To find:

Q: Wedge Sample Problem The two 20kN blocks are pushed apart by the 15⁰ wedge of negligible weight. The…

A:

Q: A manometer with water as in Figure 1.1. working fluid is connected to an air duct as shown

A:

Q: Tension What is the tension in the cable? T= Reaction at A What is the magnitude and direction of…

A: According to the given data m=15kg W=15xg=15x9.81=147.15N L=AB=5m We need to find  Tension T…

Q: how does F_BC equal 6

A:

Q: Assume you have a 30 mm in diameter AISI 1040 steel shaft welded on a rigid surface. Forces applied…

A: Given that, AISI 1040 steelDiameter of shaft, D=30 mm,Torque applied on shaft, T=40 N.mBending load…

Q: Please look at pic. Please help, I don't get part b. Thanks

A:

Q: g) Calculate the magnitude of the maximum bending stress in the beam. Enter your answer in MPa to…

A:

Q: A light fixture of negligible mass, has three applied forces acting on it as shown. |F,| = 4 kN 1.2…

A:

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: Given data,  Sprinter is having uniform acceleration of a for first t= 5.4 sec  When t= 0 initial…

Q: For the control system shown in fig-2, a) Find the values of K and K₁, such that the closed loop…

A: Given:To find:

Q: A double-thread worm has a pitch diameter of 3 inches. The wheel has 20 teeth and a pitch diameter…

A:

Q: Determine by direct integration the centroid of the area shown.

A:

Q: Difference in temperature (AT) C° (with sign) Difference in distance between test points (Ax) cm…

A:

Q: Determine the internal shear force at point C Express your answer to three significant figures and…

A:

Q: 2 ft 2 ft 3 ft A 6 ft

A:

Q: For the, 1060 H18, aluminum beam and loading shown, the beam is of rectangular cross-section with…

A: The parameters for the rectangular cross section. b=6 inh=10 inINA=500 in4Q=75 in3 Determine the…

Q: 3. FBD for AK to determine the internal forces on K: forces/reactions on the AK; a. There are b. Sum…

A: In this problem, it is asking for question (3) so we will provide the solution for question (3)…

Q: Air enters a compressor operating at steady state at 105 kPa, 300 K, with a volumetric flow rate of…

A:

Q: Find Ta,Tb,Tc

A:

Q: 02 2N Find markdore.

A: Given data : The value of force applied F=2 N The value of Distance moved by an ball d=1.1   To find…

Q: 6.51 page 330 Determine the force in members DE and DF of the truss shown when P = 20 kips. F 7.5 ft…

A:

Q: A triangular brass casting is shown. The block weighs 15.30 pounds. Brass weighs 526.7 pounds per…

A:

Q: Determine the maximum shear stress (psi) in the W250X115 beam.

A: Load in the beam F=10KN Uniform distributed load in the beam. M=2KN/m

Q: direction. The spring of stiffness k is attached to a fixed point and its undeformed length is do.…

A:

Q: Sketch a plot that contains a lateral strain for a material undergoing a temperature change which…

A: Given : Same temperature change for 2 materials one results in elastic deformation and another…

Q: 4. A pair of gears with a reduction ratio of 2.32 operating on 83mm cen- tres is required. The…

A: Since you have asked only specific question so i answer only the subpart i for you. Given Data The…

Q: The figure (Figure 1) shows a model of a crane that may be mounted on a truck.A rigid uniform…

A:

Q: 3.32. How far below the water surface should a vertical square, 1.22 m on a side with two sides…

A:

Q: a. Temperature b. Time in ambient atmosphere C. Time in furnace d. Alloying elements e. Cool-down…

A: Since you have been posted multiple questions. So, we are solving only first question for you. If…

Q: If the compact disc is spinning at a constant angular rate 0 = 355 rev/min, determine the magnitudes…

A:

Q: Using the Method of Joints, determine the force in each member of the truss, and state if the…

A:

Q: Determine the minimum shaft diameter at locations A, B, C, D, & E for an enclosed industrial…

A: The power transmitted by gear B, P1 = 25 hpThe number of teeth on gear B, Z1 = 24The diametral pitch…

Q: Determine the moment of inertia (cm4) Ty of the area shown with respect to the vertical line that…

A:

Q: Determine the moment of inertia (in mm) of the given figure with respect to x axis. Assume y-88 mm…

A: Please find the answer below

Q: 4. Develop the K for the relationship T = Kcp ŋ SN for the cone-and- plate rheometer; plate of…

A: Viscous force equation, F=AηVyF=Viscous force,A=Area of the moving plate,η=coefficient of…

Q: The figure below shows a vapor power cycle that provides process heat and produces power. The steam…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.