figue below.Select the un- age v is 24V. Each conduct Reference

Q: (b) The steel shaft has a diameter of 40 mm and is fixed at its ends A and B as shown in Figure…

A: For solution refer below images.

Q: Arrange the following steps/procedures in sketching Oblique Drawing. Write number 1-7. Copy and…

A: Oblique Drawing :  Oblique sketching is the the type of drawing which consists of pictorial view or…

Q: not read the answer. Is there a way to upload it in ano

A: Navier-stokes equation (momentum and continuity equations)

Q: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm² and…

A: Consider a virtual load Q, acting vertically downwards, is applied at point A.Draw the given truss…

Q: For the given isometric drawing, draw the corresponding top, front and right side views

A: According to the given data A isometric view of a object  We need to draw  The corresponding top,…

Q: Says.003 is wrong

A:

Q: One end of a piano wire is wrapped around a cylindrical tuning peg and the other end is fixed in…

A:

Q: Draw the orthographic Projections of given object. $30 080

A: The orthographic projections of the object include Top View, Front View, and Side View. All…

Q: 30r 20dls 20 10r 20 20 30 150 100

A:

Q: 10" 3". 30°

A:

Q: In a lathe machine tool, when the cutting tool moves parallel to the axis of rotation of the…

A: It is required to justify given statement

Q: The smallest division on the main scale of Vernier calipers is 0.1 cm. Ten divisions of the Vernier…

A:

Q: From the projected views obtain the isometric drawing.

A: According to the details provided in the question, there are three views of the first angle of…

Q: Sketch a isometric drawing for each of the three sets of orthographic drawings

A: Given: A set of orthographic projections.

Q: Draw the orthographic Projections of given object.

A: Orthographic projections are projections of a component in three directions that are perpendicular…

Q: Calculate the number of degrees of freedom The value must be a number 11 Calculate the number of…

A: Full joint is the joint which has area or surface contact, and half joint is the joint which has…

Q: Question 3) On the plate in the figure, the length L is given as L = 18 m . According to this; y 2L…

A: Given data: Image with relevant details   To determine: X and Y coordinate of the geometric center

Q: L HRP FRP (TOP VIEW) (FRONT VIEW) L (RIGHT SIDE VIEW) L

A:

Q: Q1) Create an orthographic projection of the following object. Draw the three standard views-

A:

Q: The first diagram is wrong, line AB should be longer since its length is equal to 580mm than line…

A: Given: The length of AB=580 mm Length of P2B=360 mm. So the length of AB should be greater than the…

Q: Please now answer the second question and third

A: This question is based on the concept of Braggs law of material science

Q: j) k) Solve for x (x-coordinate of the composite area's Centroid) Solve for y(y-coordinate of the…

A: (j) Write the x-coordinate of centroid for each shape. x1=200-4r3π=200-42003π=115.12…

Q: t the end of the link BC. Given the kinetic coefficie he disk is then placed against the wall.…

A: mass (m) = 17 kg angular velocity (w) = 49 rad/sec  kinetic friction (μ)  = 0.25∑ FX = FB cos 60 -…

Q: . Draw it's projections in all possible positio

A: Given: A point is 50 mm from both the reference planes. To determine: Projections in all possible…

Q: Given the multiview projection of the solid, draw the isometric view.

A: Given:Draw:The isometric view from the multiview projection of the solid.

Q: B Fig. 4

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.