10" 3". 30°

Q: What is the defect size in soda-lime-silicate glass if KIC = 750 KN m²3/2 and the typical measured…

A: Given: The fracture strength, KIC = 750 kN.m^3/2 The ultimate strength = 70 MPa

Q: A particle travels along the circular path from A to B in 1 s. If it takes 3 s for it to go from A…

A: Given: The time taken from a to B, t1 = 1 s The time taken from A to C, t2 = 3 s

Q: Design a helical compression spring to be used in a cam and follower mechanism made of oil tempered…

A:

Q: Steam enters a turbine at 1380 kPa with internal energy of 2705 kJ/kg and specific volume of 0.1655…

A:

Q: A particle is traveling along the parabolic path y = 0.25x². If x = (2t) m, where t is in seconds,…

A:

Q: Pegs A and B are restricted to move in the elliptical slots due to the motion of the slotted link.…

A:

Q: 1.41 A new absolute temperature scale is proposed. On this scale the ice point of water is 150°S and…

A:

Q: 2. Determine the slope and maximum deflection at C of the beam shown in Figure Q2. Figure Q2 с M B

A:

Q: Using the energy method, determine the vertical deflection of point D in the cantilever beam under…

A: given;3 750*10load(P)=5KN              =5*103Nyoung's modulus(E)=80GPa…

Q: The posltion of a particle is r = { (3t° - 2t)i - (4t"2 + t)j + (3ť° - 2)k} m, where t is in…

A: Given data  r = (3t2 - 2t) i - (4t1/2 + t) j + (3t2 - 2) k   To determine the magnitude of the…

Q: > 15N/m²= 1-5x 10 ³/10/cm² = 0-0015 x(10-2) 2 N/cm²= lb/ft²

A:

Q: Water flows in an open tank at a rate of 1 L/s. At the bottom of the tank is an orifice of 2 cm…

A:

Q: - As illustrated in the diagram, a cantilever beam supports a uniform distributed load of 60 kN/m.…

A:

Q: An air compressor handles 8.5 m'/min of with a density of 1.26 kg/m and a pressure of atm, and it…

A:

Q: 3. A turbine operates under steady flow conditions, receiving steam at the following state: pressure…

A: For the Given turbine  To Calculate  Power output of turbine (in kW)

Q: A syringe, containing an incompressible fluid, is oriented vertically and the plunger is slowly…

A:

Q: Determine ly and ky.

A:

Q: A particle is moving along a straight line such that its position from a fixed point is s = (12 -…

A: average speed = total distance covered/ total time taken

Q: 3. The rigid bar ABCD is supported by a pin at B and restrained by identical steel bars at C and D,…

A:

Q: Through load analysis, force and moment diagram are obtained, as shown below. Diagram below shows…

A: The force that occurs between mating gears is normal to the surfaces in contact. The axial force Fa,…

Q: Consider the given state of stress. Given: X= 6 ksi and Y= 30 ksi. + 6 ksi The normal stress is…

A:

Q: Assessment Task 1. 1 and 2 are rolling cylinders connecting shafts A and B. 3 and 4 are cylinders…

A: Given Data The diameter of the shaft 1 is: d1=25 cm The diameter of the shaft 2 is: d2=40 cm The…

Q: The figure below is a phase diagram for alloys of aluminum and silicon Atomic percentage, silicon "C…

A: Apply level rule at 576 degree Celsius at 6 wt% Si.

Q: Draw the block diagram and discuss the working principle of the following control system briefly. 5.…

A: The working principle of the flyball speed governor. Concept used: Flyball speed governor: The…

Q: Draw the block diagram and discuss the working principle of the following control system briefly. 2.…

A: The working principle of the pressure cooker. Concept used: Pressure cooker: A pressure cooker is a…

Q: Compute the elevation considering the atmosphere as a static fluid which has a final value of…

A: (a) To find: The elevation considering the atmosphere as atmospheric fluid. Given: The air density…

Q: 3. Obtain a state-space representation of the mechanical system shown below, where u₁ and u₂ are the…

A:

Q: 10. An open box is formed by cutting squares of equal size from the corner of a 24 x 15 inch piece…

A:

Q: A space to be air-conditioned has a sensible heat load of 34.9 hp and a latent heat load of 6.97 hp.…

A:

Q: In the figure below, the trusses are all stable. Compute the magnitude of reaction at C in kips. E…

A:

Q: The steel bar shown in the figure is initially constrained to just fit between two fixed supports at…

A: Given, a=15.25 mmL=0.7 m=700 mmT1=21.10 0CT2=62.5 0Cα=11.7×10-6 /0CE=210 GPa=210×103 MPa

Q: Resolve the force F2 into components acting along the u and v axes and determine the magnitude of…

A: According to the given dataF2=420 NWe need to resolve the Force F2 Along the u and V axes

Q: The rate of heat loss through 10 sf of a 3 inch thick surface is 15,000 BTUH, with a 50 degree F…

A:

Q: Steam with a flow rate of 3000 lbm/hr enters an adiabatic nozzle at 200 psia, 600 ft/min, with a…

A:

Q: Determine the magnitude of the vertical force Ay for the simply supported beam, where w = 8 kips/ft,…

A: To Find :  The magnitude of vertical force . Given :  The uniform distributed load is w=8kipsft  The…

Q: 4. Find dy/dx for xy² + y² - 2x = 5

A:

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.