I need the answer as soon as possible 001B: Materials engineer has analytical skills as well as writing and problem-solving skills. Write thesuitable answer for the following questions depending on your conclusion:(Five only)1- Why are LBM and EBM not very popular2- Why is a vacuum chamber needed in EBM?3- Why are abrasive particles not reused in AJM?4- Why is graphite considered a best tool material in EDM?5- Why is it desirable to keep the standoff distance minimum in WJM?ó- Which type of non-traditional machining processes leads to metallurgical damage? Why?Wnisonet

Dear student, According to expert guidelines I am allowed to answer only one…

B: Materials engineer has analytical skills as well as writing and problem-solving skills. Write the suitable answer for the following questions depending on your conclusion:(Five only) 1- Why are LBM and EBM not very popular

B: Materials engineer has analytical skills as well as writing and problem-solving skills. Write the suitable answer for the following questions depending on your conclusion:(Five only) 1- Why are LBM and EBM not very popular

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

When do stress concentrations occur?
How do we get 2.264 and .4415?
It says surface Temperature is not 125.49oC (look at picture I attached). What would be the correct value? Thank you.
Texts: A haulage gear is driven by a motor which develops 15 kW at a full speed of 750 rev/min. The haulage drum is 1.5 m in diameter, and the total reduction ratio of the gearing between the motor and drum is 15:5. The efficiency of the gear is 75 percent, the gradient is 1 in 25, and the rail friction is 135 N per tonne of load. The masses of the gear are equivalent to a total mass of 2.3 Mg, with a radius of gyration of 0.5 m at the drum shaft. Calculate the total load that can be hauled at the full speed. If the motor can give an excess torque of 10 percent of that at full speed, calculate the acceleration possible, assuming that the efficiency and rail friction values remain unaltered.
Please solve for me handwriting request to u please solve all for me what i ask i requested to u solve all handwriting thanks ?.
Two shafts, 1.67 ft apart, are connected by an open belt. The input shaft has a speed of 350 rpm and the output shaft should be capable of running at speeds of 950 rpm, 650 rpm, 450 rpm, 250 rpm, and 150 rpm. If the diameter of the smallest pulley on the driven shaft is 2 inches, calculate the length of the belt and the diameters of each pulleys attached at the shafts.
Please answer ASAP! Please show the complete solutions. Rate will be given. No long explanation needed. Answer in 3 decimal places. Mechanics of Deformable Bodies A steel circular shaft (G= 80 GPa) of constant diameter of 28 mm is subjected to the following torques in N-m: TA= 160; TB = 130; TC = 350; TD = 380. The directions of the applied torques are indicated in the figure The bearings shown allow the shaft to turn freely. The length of each segment is equal to 86 cm. (a) Plot a torque diagram showing the internal torque in segments (1), (2) and (3) of the shaft. Show the FBD of each segment using a double-headed arrow to represent each torque. Use the same rule of signs as in the lecture. Determine (b) the maximum stress in the shaft in MPa (C) rotation angle of pulley B with respect to pulley D. Solid shaft: J= (pi/32 X D4) Hollow: J= (pi/32xD4-d4) Note: Please Follow rule of signs and show complete FBD of each section
What is the relation between force and velocity?
A pair of forces acting directly on the material to reduce in its length are called Select one: Friction force Slipping force Compressive force Direct force
For step one, I got the same values but negative
I need the answer as soon as possible
Please derive this equation