Find the shape factor about the horizontal axes for the section shown. 12.5mm 152mm 63.5 125 63.5mm 12.5 12.5!

Q: 1. Given the following set of stadia level notes. The instrument used has a stadia interval factor…

A: Given, STA   BACKSIGHT     FORSIGHT         INTERCPETS VERTICAL ANGLES () ROD RDG (RR1)…

Q: 2. Determine the centroid and moment of inertia along x-axis of the given built- up members (Mertric…

A: To find the centroid and Moment of Inertia of the given area about the x axis (Centroidal Axis).

Q: 100mm 20mm 200mm 720mm II Locate the centroidal axis and centroidal moment of inertia of the…

A:

Q: 3.0000 R2.0000 1.0000 4.0000 2.0000 4.0000 4.0000 0000 0000 0000-

A: Handmade drawing are attached for better understanding.

Q: 100mm 30mm 30mm 160mm 30mm 120mm

A:

Q: Determine the moment of inertia of the cross- sectional area of the beam about the y axis 717mm 25…

A:

Q: A drawbridge is being raised by a cable El. The four joint loadings shown result from the weight of…

A:

Q: 6M WL 6

A:

Q: W В 20 k 20 ft A 20 ft - 15 ft -

A: Given, w=1.25K/ft

Q: 2. Determine lg-g for the T-section shown. 40mm 209.545mm 250 mm g g 100.455mm 60 mm 200 mm

A:

Q: Problem #2: Calculate the centroid (from the bottom) and the gross moment of inertia for the…

A: Given, Cross section of an uncracked section    To find : Centroid relative to bottom and gross…

Q: Q.02. The floor beam in below figure is used to support 6 meters width of a plain concrete slab…

A: GIVEN DATA: DENSITY OF PLAIN CONCRETE=22KN/m3 DENSITY OF ROCK=26KN/m3 DENSITY OF PLASTER =18KN/m3…

Q: NE 320 SUUNTO MS 00 90 SO YO CO 00 MN

A: It is quadrant bearing compass by the observation of the readings.

Q: Determine the radius of gyration through the centroid (x and y), 175 mm 35 mm YG N.A. dz 180 mm 35…

A: Given :

Q: Find x and y

A: We will divide the given C-section into three sections as shown in the figure:

Q: 47 mm 47 mm Semiellipse 26 mm 70 mm

A:

Q: Locate the centroidal axis and centroidal moment of inertia of the following section.

A:

Q: Homework: Draw shearing stress distribution of the critical section? -I 500KN 12mm 12mm 276mm 12mm…

A:

Q: Locate the centroidal axis and centroidal moment of inertia of the following section.

A: To determine: location of centroid axis centroidal moment of inertia   To answer the problem the…

Q: 785 mm 19.7 mm ------ X 33.5 mm- -384 mm- Built-up Section Typical Section Ix = 4200 x 106 mm4 ly =…

A: In this problem we nedd to calculate the moment of inertia about the centroidal axis of the built up…

Q: For the section below; i) Determine the position of the center of gravity. ii) Calculate the values…

A:

Q: TEST II: DRAW THE ISOMETRIC VIEW 20 Mm 20 20 TOP VIEW 5. FRONT VIEW SIDE VIEW 20

A:

Q: Situation 1 | Consider the figure on the right. A steel plate is used to connect a member to a steel…

A:

Q: Determine the area moment of inertia about the xo- and yo-axes, which pass through the centroid of…

A:

Q: 13. Please calculate the distance in meters of the following stadia images with a k=100. The scale…

A: please look into the solution provided.

Q: For the angular section shown: Which of the following most nearly gives the moments of Inertia Ix…

A: To find moment of inertia about x and y axis

Q: Illustrate and briefly discuss the procedure in measuring horizontal distances by taping

A:

Q: 785 mm -19.7 mm 33.5 mm- 384 mm- Built-up Section Typical Section Ix = 4200 x 10° mm ly = 315 x 10°…

A:

Q: Q:Analyze all the guns in trusses [2 A 6mm B 3mm 1320kn 3mm C 3mm R 70 2640kn 3mm D K E

A: Given: A truss is shown in the figure. Sign convention: Force Tension: positive  Compression:…

Q: Compute the azimuthof the missing side. (Format: 000deg00min) 00- numerical values LINES AZIMUTH…

A:

Q: Observe the image shown. In what type of perspective has the image been drawn? 0 2018 chuvipro /…

A: Perspective drawing: Perspective Drawing is a technique that is used to represent the spatial depth…

Q: 62.5mm 600mm 62.5mm 350mm Pn

A: Compression member is a structural member which is primarily subjected to axial compression. If…

Q: Compute the ¯Ix and ¯Iy for the annular region.(Ans: Ix = 4.084 × 106 mm4, ¯Iy = 0.816 × 106 mm4)

A: Given, R = 60 mm r = 40 mm    To find : Moment of inertia Ix and Iy

Q: 152 x 152 x 23 UC Frame Beam Diagram 28.2KN Self Load 805N 28.2KN 2.0m Ra 75 3.5m Pulley and shaft…

A: In Both frames, deflection is determined using Macaulay's method. The steps to determine deflections…

Q: Draw the orthographic views of the object below with dimensions. (Top, Front, Right views) m,00…

A:

Q: 53 32 32 53 L44 -t- 44 Dimensions in millimeters Answers: Ix = (106) mm4 ly = i (10°) mm4

A:

Q: For the angular section shown in figure 11: Which of the following most nearly gives the moments of…

A:

Q: Determine the x- and y- coordinates of the centroid of the given area. 65m 105mmi 40mm -- 240 mm

A:

Q: Compute the distance or spacing between stadia hairs the stadia interval factor is 99 and focal…

A:

Q: Determine the location C(x,y) of the centre of mass for the shaded area given

A:

Site Plan Requirements

A site plan (also known as a plot plan) is a diagram or process to show the proposed improvements on an existing property. A site plan is important, as it provides information regarding the landscape features of a given plot of land.  Zoning is done or can be understood with the help of a site plan.