Answered: Find the resultant of the following…

Find the resultant of the following vectors: d, = 180 km E30° N d2 = 120 km W45°N Use the following methods a. Parallelogram Method b. Polygon Method: c. Triangle Method d. Component Method

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.43P

See similar textbooks

Related questions

Q: A belt conveyor transports 18 tonnes per hr at 20°. Determine the speed reducer power factor to lift...

A: Given Datam=18T/hrN=1750rpmS=33.5mV=61m/min

Q: ss of the rigid flange at C. meter of AC = 20 mm. er diameter of AC = 40 mm solute maximum shear str...

Q: Longitudinal joint `Girth joint

A: GIVEN DATA- LONGITUDINAL JOINT STRENGTH 500KN/m GIRTH JOINT STRENGTH 220KN/m PRESSURE P=2MPa WE HAVE...

Q: In the flow curve for pure aluminum, the strength coefficient = 175 MPa and strain-hardening exponen...

Q: Determine (a) the equation of the slope and deflection of the elastic curve for the simply supported...

Q: The loads are applied to a structure as shown. the structure is supported by a pin at A and by a rol...

Q: soap bubble with a diameter of 2.03" is to be enlarged by blowing air into it. If the surface tensio...

A: Given:d1=2.03 inσ=0.0041 lbf/ftd2=4.85 in

Q: mpressing air to 7 bar, temperature rises to 40oC. Determine the following: a) Quantity of water bef...

Q: 1. In the set-up shown, a rectangular gate, ABCD, is used to store layers of oil and water. The weig...

Q: a) A Diesel engine is working with an injection pressure of 2500 bar and it is cap mode. Briefly exp...

A: given; (a) Diesel engine working (b) difference between PFI and GDI

Q: Please provide equations that you are using so I can follow along and learn how to do this and inclu...

Q: Knowing that the tension of cable AB is 75 N. Determine the moment of force AB about (a) point C a...

Q: What is the polar moment of inertia of a solid steel shaft in mm^4 that will not twist through more ...

A: Given data, T= 44kN.m = 44 N.mm L= 6 m = 6000mm G= 83 GPa = 83000 N/mm² θ= 2°

Q: Modern ignition cables contain fiber cores that act as in the secondary circuit to cut down on radi...

A: The ignition's job is to distribute the electric current from the transformer to the spark plugs ...

Q: A sub-marine with its axis 15 m below water surface fitted with pitot tube moves horizontally in sea...

Q: The mechanism set up with m, m, and weightless pulleys is as shown in the figure. Then, the masses a...

A: Given Datag=10m/s2m1=1kgm2=4kg Friction are ignored ***As per our company policy we are supposed to ...

Q: ected to torsion by torques T applied at the ends (see figure). The bar is 10 in. long, and the insi...

Q: Explain about any two types of belt drives with a neat diagram.

A: GIVEN DATA- BELT DRIVE TOPIC GIVEN WE HAVE TO EXPLAIN ANY TWO TYPE OF IT

Q: P3.143 The large tank of incompressible liquid in Fig. P3.143 is at rest when, at t = 0, the valve i...

Q: Convert the following 4th order ODE into a system of four first orde ODES of the form dy/dt f(t,y). ...

Q: 120 MPa in compression. (The working stress in compression is smalle to reduce the danger of bucklin...

Q: PROBLEMS 1 - A ( 200 N ) weight of the block shown in fig. is supported by a pin and bracket at ( A ...

Q: A short column tube of length L = 400 mm is loaded by a compressive force P. The outside and inside ...

Q: 6 cu. m of oil weighs 46,800 N, calculate the following a. Unit weight in N/cu. m b. Density in kg...

A: Given:V=5.6 m3W=46,800 N

Q: total drill time in seconds is

A: Given data; In a single pass drilling operation,Hole oil diameter,d=15 mmDrilled in a steel plate ha...

Q: P3.82 The model car in Fig. P3.82 weighs 17 N and is to be accelerated from rest by a 1-cm-diameter ...

Q: centroidal moment of Inertia

Q: Boxes (or certain production parts) are moved by a double-acting cylinder away from a gravity-feed m...

A: this question is srawing with ISO symbol the answer in step two

Q: For the beam and loading shown, determine the absolute values of the shear and bending moment at 2.5...

Q: Determine the smallest safe diameter of the solid steel shaft if the maximum shear stress is 50,000 ...

Q: Use MATLAB to c

A: Question is not visble. But we don't have to send the matlab aceses to accounts.

Q: Knowing that tanks exposed into the atmosphere have pressure of atm. What is the design pressure? a...

A: The tank design on basis of pressure can be done by three ways: Atmospheric pressure design Full va...

Q: Give an example of an interconnected system of two tanks so that: the system is homogeneous the sys...

Q: of 300 mm running at a speed of 2950 rev/min delivering 45 similar spare pump running at a speed of ...

Q: Figure below shows a four-bar linkage (non-scaled diagram) at an instant. The input angle is equal t...

Q: 1. Determine the other properties of the steam for the following conc d) P= 13 Mpa, h= 3191.3 kJ/kg-...

Q: A 1 kg block B is moving with a speed of 2.55 m/s as it strikes the 0.3 kg sphere A which was at res...

Q: 900 Ib. 400 Ib. 60 Ib./ft 4 ft 8 ft 6 ft

Q: A 120-mm diameter bolt is used in a clevis. Determine the shear stress on the bolt if a load of 350 ...

A: Given data, d= 120 mm F= 350 kN =350000 N

Q: determine the properties of H2O using steam table 1. saturated liquid at T= 253.5 deg C please e...

A: Given condition T = 253.5 °C The aim is to determine the properties of saturated liquid at 253.5 °C ...

Q: 90 MPa 60 MPa 20 MPa

A: From the data given in question, Normal stress in x-direction = σx = -20 MPa Normal stress in y-dire...

Q: 1. What kind of corporation you want to work in? 2. What technical skills you have to acquire

A: 1) A partnership is a lawful substance that its proprietors control through shares. During the cours...

Q: A device's outer cylinder diameter is 7" and its distance from outer cylinder to the inner cylinder ...

Q: A venturi tube is used to determine the airspeed at the throat/test section. During the test, a rais...

Q: Determine the member end moments at b, Mba and Mbc, in the following structure. EI constant 300kN 2m...

A: Given dataP=300kNRoller support at C which exhibit only vertial force

Q: Three plates are held together by 2, 11 mm diameter bolts. If a 16 kN load is applied to the plates ...

Q: A wheel tractor has a 200HP engine.if it is operating at an altitute of 1000m above sea level, at an...

Q: cotter joints supports a load varying from 3000 kgf in compression to 3000 kgf in tension. The tensi...

Q: A turbine is driven by a system that enters the turbine at the ff. conditions: 200 kg/h, 39 atm, 501...

A: mass flow rate (m.)= 200 kg/h= 200 kg/3600 sec= 0.0555 initial temperature ( Ti)= 501 C speed (C1)= ...

Q: An oil is acting as a lubricant for a pair of cylindrical surfaces such as those shown in The angula...

A: Given that, Speed of outer cylinder, N=7908 rpm,Radius of outer cylinder, ro=5.06 cm=0.0506 m,Cleare...

Question

Find the resultant of the following vectors:
di = 180 km E30° N
dz = 120 km W45°N
Use the following methods
a. Parallelogram Method
b. Polygon Method:
c. Triangle Method
d. Component Method

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 10 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

the resultants, so you need to add the vectors together. Keep at least three digits, or leave in exact form until the final answer, to avoid this problem
Please solve using vector method.
4. Use Geogebra and the Klein-Beltrami model to show that a pentagon with five right angles and a hexagon with six right angles can be drawn in hyperbolic geometry. Hint: Start with two lines that have a common perpendicular.Find the poles of those two lines, then draw an appropriate line through each pole, so on.
Solve using superposition
slove it by complex algebra method
a. What is the position vector that starts at -50j and ends at 50 j? b. What is the position vector that starts at (-50 i - 20 j +10 k) lb and ends at (50 i + 20 j -10 k) lb c. What is the resultant sum of the moments in Cartesian vector form? Round your entries to the nearest whole number.
Let R correspond to a right-hand rotation of angle about the x3-axis. (a)Find the matrix of R². (b)Show that R² corresponds to a rotation of angle 20 about the same axis. (c)Find the matrix of R" for any integer n.
Graphical Method : Polygon Method F1 - 150N, 30° N of E F2 - 100N, 60° E of S 1) Find the Length and Angle 2) Find Resultant Force Vector Magnitude and %Error 3) Find Resultant Force Vector Direction and %Error
Solve for the following problem and show pertinent solutions using Polygon Method only.
Two lines in the x-y plane are described by the expressions: Line 1: x + 2y = -6 Line 2: 3x + 4y = 8 Use vector algebra to find the smaller angle between the lines at their intersection point. a. BAB = 10.3° O b. OAB = 13.3° O c. BAB = 31.3° O d. BAB = 30.10°
Solve the following with diagram
Compute F(s) = and polar form. s(s+2) (s+1)(s+10) strikt when s=2-3j. Express the result both in Cartesian coordinate GLG KEEP KIDS