Find the pressure at point 2 given the isometric drawing of the commercial steel pipeline indicating the straight pipes length and with the following data below: Loss coefficients: • check valve, k = 5.0 • gate valves, k = 0.20 • elbows, k = 0.75 • flowmeter, k = 13.0 Pump flowrate = 10 m3/hr Fluid power adding by pump = 3.7 HP Pressure at point 1 = 60 kPag Pipe inside diameter = 50mm Viscosity = 0.17 Pa.s Specific gravity = 0.89 Pipe inside surface roughness = 0.00015 ft.

Q: For the series-parallel system of Figure below, all pipes are 6-cm-diameter galvanized iron new. If…

A: In the Pipe flow system water is flow through the pipe as closed conduit having circular…

Q: Problem 1 A flow occurs between an inner solid cylinder of radius 'b' and an outer pipe with a…

A: The average velocity in the annulus can be obtained using the Darcy-Weisbach formula:…

Q: (Q)A pump running at 1,440 rpm has to support a load of 10 kN. Journal diameter is 130 mm. Design a…

A:

Q: The Hagen-Poiseuille equation for the laminar flow through a circular pipe is: AP = where AP is the…

A:

Q: Q5: For the system shown in figure. Find the total head loss from (A) to (B). the pipe…

A:

Q: For the parallel-pipe system of D=3 in L= 250 ft Fig. each pipe is cast iron, and the pressure drop…

A:

Q: Design the rectangular duct system shown in figure below using equal friction method with frictional…

A: Given Data∆P=1Pa/mh=300mmQD=0.6m3/s=QF=QI=QJ

Q: 80mm; de coefficient respective

A: d=80mm=0.08m.....same for delivery and suctionf=0.007Total length = 3m+6m=9m

Q: -. Calculate h, (loss head) in a pipe through the water is flowing...

A: V=3 m/sd=250mm=0.250ml=100 mk=0.4ζ=6ρ=100 kg/m3ν=1*10-6 m2/s

Q: =// A rotary filter is required for the filtration of a slurry to produce 10 m' in 3500 §, the…

A:

Q: Compute the volumetric gas flow in the duct (m3/s)

A: Pitot tube Pitot tube is a flow measurement device used to measure fluid flow velocity. Pitot tube…

Q: In Fig. a thick filter is being tested for losses. Theflow rate in the pipe is 7 m3/min, and the…

A: Given: The flow rate in pipe, Q = 7 m3/min The upstream pressure in pipe, P = 120 kPa The diameter…

Q: A water is to transport in a 500 mm diameter pipe and connects two reservoirs. The pipe is 3000 m…

A:

Q: A designer needs a quarter-turn valve to flow approximately 10 GP an inlet pressure of 3000 psig…

A: Flow Rate Equation

Q: A series of commercial steel pipe which length, I = 20 in. and diameter, d = 0.8 in. is placed on…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: QI A 0.5 inch diameter water pipe is 18 m long and delivers 19 L/min. What fraction of this pipe is…

A: Given DataQ=19L/minD=0.5 inL=18m

Q: The pressure difference between two points in pipe due to turbulent flow depend on velocity,…

A: ∆P=fV,D,μ,ρ,ε,L

Q: Water at 9 °C flows through a 3m of 1 1/2 inch type L copper tube, through a 90° standard elbow,…

A: Given Initial temperature Ti=9∘ C For 1 1/2 inch type L Copper tube  Outer diameter do=1.9…

Q: A is 2000 m gas flow line (6-in) and B is 2500 m liquid flow line (4-in) should be onnected both…

A:

Q: Determine the velocity in the discharge side. Determine the velocity on the suction side. Determine…

A:

Q: Problem : Taking into account only the local resistances, determine the level difference in the tank…

A:

Q: Problem 1: For the system shown in the diagram below, let 4z = 80 m and L = 185 m of cast iron pipe…

A: To determine:Pipe diameter(D)

Q: 3 whot is the pressure in a 9.7-in bore horizontal pipe, :f the bore of the pipe norrows to 4.1 in…

A: Fluid Pressure Fluid Pressure is the pressure at point in the fluid arising due to weight of fluid.…

Q: ancellation and do not use shift solv

A: Given-Information:- ρ = 875 kg/m3∆P = p1-p2=78 psi = 6032.91 kN/m2d1 = 25.4 mm =0.0254 md3 =0.20…

Q: Q2 .. h, are 12m. The pump efficiency is 79%, and the pump is driven by an electric motor. A pump…

A:

Q: For the figure below find 1) Volumetric Flow rate (Q) MH2 O 1.677 O 6.478 18.453 12.146 MH1 CHW = 80…

A:

Q: A pitot-static tube is used with a mercury (SGHg =13.6) manometer to measure the flow of an inviscid…

A:

Q: Estimate the weight of a 25 km gas pipeline with a DN 600 mm, OD of 610 mm, and a wall thickness of…

A:

Q: A fluid flows in a variable arca pipe with negligible viscous effects. At point 1, the pressure is…

A:

Q: A two branch duct system of circular duct is shown below. The fittings have the following equivalent…

A:

Q: Consider a positive displacement pump; Shaft speed is 1800rpm Pump push 0.003gal/revolution Leakage…

A:

Q: An oil well has the following specifications; • Tubing diameter = 2.875” • Tubing roughness = 0.0254…

A:

Q: An 18-in-diameter centrifugal pump, running at 880 r/min to pump water at 20°C through 75 m of…

A: Given diameter = 18 in running at =880 r/min ε=0.15

Q: 1-For the horizontal water pipe shown , find the change in diameter if the far and of pipe is : a)…

A: Given: To determine the change in diameter

Q: Consider water flow through a pipe 6 m long and internal diameter 300 mm. The head loss due to…

A: Length of pipeL=6mDiameter of pipeD=300mm=0.3mhead loss due to frictionhf=6mValue of surface…

Q: Starting from Tw find 1, 1 2 1 3 and proof the following equation f and Re using dimensional…

A:

Q: A compressor delivers 2000 cfm of air through a pipe at a receiver pressure of 140 psig. What…

A: To find: The diameter of the pipe. Given: The pressure in the pipe is P=140 psig. The air delivery…

Q: Find the Kilowatt loss in (1000 m) of ( 50 cm ) diameter pipe for whish (e 0.05 mm when crude oil at…

A:

Q: A flow nozzle with a throat diameter d of 6-inches is being used to measure the flow rate of hot…

A: Given Data: d=8 inT=80oF12 inch SCH 80 pipe∆P=1.46 psiC=0.96   To Find: The flow rate of water in…

Q: What are the flow Q and the velocity V when total head loss is H = 25 m?

A: Total head loss,(Hloss)=25 m. Kentrance=1Kglove valve=10Kelbow=0.9Kexit=1D=20mmf=0.02L=9m. Determine…

Q: Please check attach file

A:

Q: In the design of a 500m long water pipeline it is proposed to keep head loss, hf, less than 6m for a…

A:

Q: Q5: For the system shown in figure. Find the total head loss from (A) to (B). the pipe…

A:

Q: 2) For the same system of question 1, let Az = 80 m and L pipe diameter for which the flow rate will…

A: Pipe diameter is 18.3 mmExplanation:

Metrology of surface finish

In general terms, the application of scientific principles in the study of measurements is known as metrology. When speaking about measurement, it could be of time, length, microstructures, grain structures, internal crystal discontinuities, surface roughness, measurements of angles, height, width, and so on. While coming to the domain of mechanical engineering, metrology is considered the science of measurements of surface finish, length, surface texture, and angles.