12.10Find the flow rate in the siphon in figure 12.39. What is the pressure at point A,which is 150 mm above the outlet? Estimate the minimum pressure in the system.1.8 m#11Curva de retorno cerradaPetróleo, S=0.8= 0.01 N-s/m²100-mm-diamtubería lisa3.6 m150 mm50-mm diam boquillaPérdida = 0.1Figura 12.39 Problema 12.10.I

Answered: Image /qna-images/answer/8b6d327a-3efe-4cae-b99a-083e6fb61511.jpg

Find the flow rate in the siphon in figure 12.39. What is the pressure at point A, which is 150 mm above the outlet? Estimate the minimum pressure in the system. 1.8 m fam Curva de retormo cerrada Petróleo, S=0.8 -0.01 N-s/m² 100-mm-diam tubería lisa 3.6 m -150 mm 50-mm diam boquilla Pérdida 0.12 I

Find the flow rate in the siphon in figure 12.39. What is the pressure at point A, which is 150 mm above the outlet? Estimate the minimum pressure in the system. 1.8 m fam Curva de retormo cerrada Petróleo, S=0.8 -0.01 N-s/m² 100-mm-diam tubería lisa 3.6 m -150 mm 50-mm diam boquilla Pérdida 0.12 I

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two reservoirs are filled with kerosene, each having a cross-sectional area of 300 mm2. The connecting tube has a cross-sectional area of 15 mm² and contains mercury. Determine h if the pressure difference is 40 Pa. Take density of mercury as 13 550 kg/m3 and density of kerosene as 814 kg/m3
I need the answer as soon as possible
ellen 10
An oil (S = 0.85, v = 1.8x105 m²/s) flows through 0.1m diameter pipe at 2m³/sec, 150m long. Find the head loss in the flow if the used pipe is cast iron type (e = 0.26mm).
3.Consider a system with a specific discharge of 3 m2/s as shown in Figure 2. Thedepth, y1, upstream of the step is 2 meters. The downward step height is 0.2 meters. (a) Determine the Froude number of upstrem and downstrem of flow(b) Determine the upstream and downstream specific energy, E.
Solution step by step..
Show step by step solution for num 7
The cylindrical tank shown has a hemispherical end cap ABC contains water as shown in the figure. Compute the resultant force of the fluid on the end cap ABC.
Calculate the discharge from a tubewell of 20-cm diameter penetrating fully into a confined aquifer of 20-m thick and having a permeability of 40 m/day. The drawdown in the well is 3 m and zero drawdown at 300 m from the well. Q = 2.72 T (H-h) log 10 R/r Select one: O a. 1315.9 O b. 1303.7 O C. O d. 1257.3 1200.4
A 5 cm diameter siphon tube is used to empty the pool and discharged it into air (figure below). Determine the discharge rate through the tube and pressure inside the house at point 1, 2, and 3. Assume no losses. Aut 3 2m 7m
Q(1): A horizontal rectangular stilling basin is used at the outlet of a spillway to dissipate energy. The spillway discharges 13m'/s and has a uniform width of 12m. At the point where the water enters the basin, the velocity is 10m/s, compute: • The sequent depth of the hydraulic jump, The length of the stilling basin, • The energy loss in the jump, • The efficiency of the jump (the ratio of specific energy after to the specific energy before the hydraulic jump, • If the thickness of the basin is 0.75m, and the sieve analysis for the site soil indicate the d50 is 0.05mm, are the requirements of scour design satisfied or not?
11.20 3. Parallel Pipe Three pipes are in parallel with a total head loss of 20.3 m. The pipe data are pipe 1 2 3 L, m 100 150 80 d, cm 8 6 4 €, mm 0.24 0.12 0.20 €/d 0.003 0.002 0.005 The fluid is water, p = 1000 kg/m³, and v= 1.02 x 10-6 m²/s. Calculate the total flow rate in cubic meters per hour, neglecting minor losses.