Figure Q2(a) shows a circuit configuration of DC ammeter by using PMMC instrument. Determine and analyze the following: i You are required to modify a PMMC instrument with a full-scale deflection current of 2 mA into a 0-150 mA ammeter application. Given the internal resistance, Rm of the meter is 100 2, find the required shunt resistor, Rsh need to be installed into the circuit. i By using the modified circuit as in (i), you are required to improve that circuit which capable to measure a current up to 1 A. What will be the value of the new shunt resistor? Hint: add up a new shunt resistor with original Rsh is maintain.

Figure Q2(a) shows a circuit configuration of DC ammeter by using PMMC instrument. Determine and analyze the following: i You are required to modify a PMMC instrument with a full-scale deflection current of 2 mA into a 0-150 mA ammeter application. Given the internal resistance, Rm of the meter is 100 2, find the required shunt resistor, Rsh need to be installed into the circuit. i By using the modified circuit as in (i), you are required to improve that circuit which capable to measure a current up to 1 A. What will be the value of the new shunt resistor? Hint: add up a new shunt resistor with original Rsh is maintain.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

It is conceptually possible to produce extrinsic sil- icon with a higher resistivity than that of intrinsic silicon. How would this occur?
Three Phase Uncontrolled Half Wave Rectifiers find the value of Voltage and Currents (output de and Root Mean Square) with all the proved, then sketch the curve from 0-2 on these axes (vs, vo, ia, ib, ic, io) explain its operation.
The four diodes used in a bridge rectifier circuit have forward resistances which may be considered constant at 1 ohm and infinite reverse resistance. The alternating supply voltage is 220 V r.m.s. and load resistance is 580 ohm. Calculate (i) mean load current and (ii) power dissipated in each diode.
(b) A clamper circuit has 20 Vp-p, 100 Hz square wave input voltage. The circuit consists of silicon diode IN4001 as shown in Figure Q2(b). 0.1 µF D R Vi(t) 50 k2 Vo(t) Figure Q2(b) (i) Determine the output voltage for all input voltages values. (ii) Sketch the overall output waveform, V(t).
You are an electrician working on an overhead crane. The crane uses a large electromagnet to pick up large metal pipes. The magnet must have a minimum of 200 VDC to operate properly. The crane has an AC source of 240 V. You are given four diodes that have a peak voltage rating of 400 V each. These diodes are to be used to form a bridge rectifier to convert the AC voltage into DC voltage. Is the voltage rating of the diodes sufficient? To the nearest volt, what will be the DC output voltage of the bridge rectifier?
I need the answer only those parts. vi,vii,viii,ix,x, Please provide correct solution. And provide **ALL** those parts what i mentioned ( vi,vii,viii,ix,x) WILL UPVOTE YOUR ANSWER IF YOU PROVIDE CORRECT SOLUTION OF VI,VII,VIII,IX,X
What are the different integrated circuits and describe the characteristics of each.
An AC voltage controller with common cathode has O a. two diodes to be conducted at a time b. one SRC to be controller at a time O c. two SRC to be controller at a time O d. four diodes to be conducted at a time
Answer a,b,c,d
C4 R1 Vout For the precision rectifier circuit shown in Figure C4 what is the correct operation for the circuit if a Sine wave is 10k D1 R2 LM324 VEE applied to the input signal VIN? Vin D2 10k OUT V3 U1A Figure C4 A. When VIn is negative the circuit operates as unity voltage follower providing an in phase sine wave at VouT. When VIN is positive the circuit conducts but only to one diode drop, B. When VIn is negative the circuit operates as an inverting amplifier providing an inverted sine wave at VouT. When VIN is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, c. When VIn is negative the circuit operates as an inverting amplifier providing an in-phase sine wave at VOUT. When VIn is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, D. When VIn is negative the circuit operates as unity voltage follower providing an inverted sine wave at Vour. When VIn is positive the…
A charging circuit that will deliver constant DC current will be designed. The input of the circuit is 220V / 50Hz AC and its outputIt will be 5V / 2A DC.The circuit will consist of 3 parts:AC transformer will reduce the voltage on the inputii. AC rectifier circuit will convert low AC voltage to DCiii. Current source, this part will keep the current at the output constant.You determine the transformer drop rate in the first part. Its output is low voltage ACas the source and design the second and third parts accordingly.
one SCR in anti parallel with firing angel of 90° for the 30. A single-phase voltage controller, using a diode, feeds a load R and Vs = 230 V. For a SCR, the PMMC voltage connected across R would read