Figure, 3m 3m 2m E P = 1KN 2m wall cable D 6m uniform rigid bar B A 4.

Q: Angle of the resultant R (in degrees, measured counter-clockwise from the positive x-axis)

A:

Q: Ro00 # 5' %23 5' 2. 1o00# а. Determine all ZFM and state the rule number you used for each of them…

A: Consider the figure, Here, T is the tension and C is the compression.

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy…

A: Determine the normal stresses in the aluminum and bronze rods?

Q: The magnitude of the reaction at the roller support is ... 4 kN 15 kN 45° D E F 4 m A В C 10 kN 3 m…

A:

Q: what do columnar joint and mud-cracks have in common?

A: Like mud-cracks, columnar joints form from volume contraction. In the mud-cracks, volume decreases…

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy…

A:

Q: A 6-m simply supported box beam is loaded as shown in the figure. Determine the maximum flexural…

A:

Q: Determine the forces in each members of 40 EN 3 m the truss loaded as shown. Tabulate the results…

A:

Q: AL SUrtace With an unkhown thictional coefficient egligible frictional coefficient. The panel has…

A:

Q: a.) What is the value of (theta/angle) to obtain the smallest possible value of P so that the crate…

A:

Q: consider the 20m beam shown • what is the location of the absolute maximum moment from the center of…

A: Solution- The end consequence of shifting weights will be,R=8+32+2R=64kN To determine the location…

Q: B

A:

Q: Determine the magnitudes of the reactions at A and B for the beam subjected to the uniform load…

A: Given beam:-

Q: A

A:

Q: beam loaded as shown. (a)What is the Value of horizontal reaction at the fixed support? (b)What is…

A:

Q: B 0.75 m 55⁰ A 1 m 0.5 m 50 N 75 N-m

A: Given values: Consider the given structure and draw the free body diagram to calculate the unknown…

Q: 1. A solid steel shaft in a rolling mill transmits (10 + 1) kW of power at 2 Hz. Determine the…

A:

Q: The given truss shown is supporting the load R = 108.8 kN on B. The truss has roller support at D…

A: Given: Required: Reaction at D Horizontal reaction at E Vertical reaction at E Note: As per…

Q: 3. (c) A square steel bar of dimension 50 mm × 50 mm × 150 mm is subjected to an axial load of 250…

A: Size of bar 50mm x 50mm x 150mm P = 250 kN or 250,000 N

Q: determine the normal stresses in the aluminum and bronze rodsa

A:

Q: (a) Figure Q3(a) shows a structural element which is subjected to pure shear, Oxy acting on…

A:

Q: A hollow shaft of external and internal diameters as 100 mm and 40 mm respectively is transmitting…

A: Given data- A hollow shaft, External diameter D=100 mm, Internal diameter d=40 mm, Speed N=120 rpm,…

Q: Problem 16.3: The temperature of the solid 20mm diameter post CD is increased by 50°C. Determine the…

A: Given, diameter of CD =20mm∆T=50° CI=225×106 mm4Est=200 GPaν=0.32α=12×10-6 /°C

Q: Weight of a homogeneous bar AB is 600 lb. Calculate the reactions at supports A and B. 120 vit

A: Given: A simply supported beam carrying a uniformly varying load (UVL). Magnitude of UVL at support…

Q: A flat steel plate is of trapezoidal form and uniform thickness of 10mm. The plate tapers uniformly…

A:

Q: shear stress of 100 MPa in the bronze segment,

A: Given data- Diameter of rod (D) = 120 mm = 0.12 m Maximum shear stress(£) = 100 Mpa Length of bronze…

Q: C and AD so that the resultant of the three forces applied at A is vertical. 18 m

A:

Q: Two blocks A and B, each having a mass of 7.5 kg, are connected by the linkage shown. Neglect the…

A:

Q: Determine the reactions at A and B for the steel bar and loading shown in the figure, assuming a…

A: Given: EAC = 1.2 ECB Determine the reactions at A and B

Q: Question A solid shaft of circular cross-section is subjeted to torque T which produces a maximum…

A: A solid shaft of circular cross section is subjected to torque T. Produces a maximum shear stress τ.…

Q: Determine the vertical reaction at support B in kN-m. w = 15 kN/m L1=7m L2=4 m L1 W L2 B

A:

Q: 3. Given the figure below, compute for the reaction at A and B and maximum stress of the beam. The…

A: ##Calculation of Support reaction and Maximum stress##

Q: Calculate the reaction force at joint H and joint A.

A: Moment at hinge is zero.

Q: 2.5m 15kN/m 2.0.m 1 20m Figure 5

A:

Q: Can the system in given figure be in static equilibrium in the position shown? The uniform bar AB…

A:

Q: 150 lb/ft -6 ft 8 ft

A:

Q: The angle of inclination of the smooth surface is 35° from the horizontal. The weight of the body is…

A:

Q: 10 kN В y 6 m 3 m D 3 m A C 60 kN

A:

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy…

A:

Q: , GE, and GD of the cage system for the loading condition given in Figure 2 Calculate the rod…

A:

Q: 10. Determine the reaction at the roller support and draw the bending moment diagram for the beam…

A: A propped cantilever beam is given with propped end at A and a fixed end at B. The beam is loaded…

Q: D (5000 mm2) (4000 mm) E (5000 mm) 3 m 4000 mm) (S000 mm?) B (5000 mm?) A 100 kN 2 panels at 4 m 8 m…

A:

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy…

A:

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.