Figure 2 below shows an L-shaped steel in one of the numerous steel-sections of the high-rise Tun Razak Exchange Tower in Kuala Lumpur. Replace all the loadings with an equivalent resultant force and couple moments on point B and; (a) Find the resultant force systems. (b) Calculate the direction angles of the resultant force systems. (c) Determine the resultant moment at point B. (d) In your own words, explain and discuss what an equivalent system is. 50N/m 50N/m B 4m 6m 100N/m

Figure 2 below shows an L-shaped steel in one of the numerous steel-sections of the high-rise Tun Razak Exchange Tower in Kuala Lumpur. Replace all the loadings with an equivalent resultant force and couple moments on point B and; (a) Find the resultant force systems. (b) Calculate the direction angles of the resultant force systems. (c) Determine the resultant moment at point B. (d) In your own words, explain and discuss what an equivalent system is. 50N/m 50N/m B 4m 6m 100N/m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A T-beam with drawn x and y axes is shown in figure 2. Determine the moments of inertia of the beam.
Determine the magnitude of the pin force at A. Assume W = 795 lb, a = 3.9 ft, b = 2.8 ft, r = 7 in. r W C Answer: A = i a B A D lb b
A steel column carries an axial load of 819 kN and a moment of 63 kN-m at the top and moment at the bottom which is only70% of the moment at the top. The two moments are in opposite direction and applied about the x-axis and the steel section has the following properties: A = 13172 mm2 rx is 109 mm ry = 94 mm Sx = 1200 x 103 mm3 K = 1.0 L= 3.6 m E = 200,000 Mpa Fy = 248 Mpa Use NSCP specification for compressive stress and Fb =148 Mpa. Determine the Compressive Stress if Axial load only existed.
In the figure, what is the bar force of member EF in kN ? 10 KN 50 KN 40 KN D 4 m 2 m 2 m O 50- C O 50 - T O 40 - C
A crate with a mass of 250 kg is held in equilibrium by three ropes attached to a steel ring. a d3 d₁ d5 B A 5.5 m 4 m d2 3.5 m 2m d₁ Z 3 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value d₁ 2 m d₂ d4 a. Determine the magnitude of the force/tension in cord A, TA. b. Determine the magnitude of the force/tension in cord B, TB. c. Determine the magnitude of the force/tension in cord C, Tc. Round your final answers to 3 significant digits/figures. The magnitude of the force/tension in cord A is The magnitude of the force/tension in cord B is The magnitude of the force/tension in cord C' is d5 kN kN kN
2.2 Please show your complete solution.
SHOW THE DIAGRAM AND YOUR COMPLETE SOLUTION: statically determinate beam is loaded as shown in the figure below. Determine the following: 1. Determine the force acting in the internal connection. А, 30 KN.m 1.5 m Im B 1.5 m O L=6m 10 KN internal hinged 1.5 m 1.5 m E
A truss is loaded as shown in the figure. Determine the following: a) Vertical component of the resultant force and its location from A. b) Horizontal component of the resultant force and its location from x-axis.