Fig.(3-11) shows the member AC is supported by a round structural steel tie rod BD and a pin at A, neglect the weight of member AC and assume that the ultimate strength (G) of structural steel rod is 490 MPa in tension and that the ultimate shear stress () of the pin is 315 MPa. Using a factor of safety of 3.5 for both tension and shear, find the minimum required diameters of tie rod & the pin. the rod D

Fig.(3-11) shows the member AC is supported by a round structural steel tie rod BD and a pin at A, neglect the weight of member AC and assume that the ultimate strength (G) of structural steel rod is 490 MPa in tension and that the ultimate shear stress () of the pin is 315 MPa. Using a factor of safety of 3.5 for both tension and shear, find the minimum required diameters of tie rod & the pin. the rod D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The strain at point A on the bracket has components €g = 330 (10-6), e, = 560 (10-6), Yxy = -570 (10-6), e; = 0. Correct Part B Determine the maximum shear strain in the x - y plane. = 6.15x10-4 'in-plane Submit Previous Answers Correct Part C Determine the absolute maximum shear strain. (Figure 1) Figure < 1 of 1 vec -4 Yaa = 7.99 • 10 max Submit Previous Answers Request Answer X Incorrect; Try Again
6
0.16
a) Two bars of different size form a pin-connected frame that supports a Load 'P' at point A as shown in the Fig. 3. What safe load P (kN) can be applied if the allowable stress of 120 MPa is not to be exceeded? Assume buckling has been prevented. Allowable stress is based on a factor of safety of 2.0. Cross sectional area of the rods AB and AC are given in the adjacent table as per last digit of Roll number. What is the failure load? Last digit of Area of AB | Area of AC Roll No. 1, 2, 4 & 7 200 mm 230 mm“ 3, 6 & 8 160 mm- 190 mm² 5, 9 & 0 180 mm 210 mm 2400 1600 Fig. 3 b) Two square bars are of equal length but have different size as shown in Fig. 4. Compare the maximum stress in the two bars if they are to receive the same input of energy from axial load. Given, m = (2 + last digit of your roll number). 2a 5.x m.x Fig. 4 last digit of roll=1
QUESTION 6 A bar of uniform cross sectional area- 168.290 mm2 is fully fixed at supports A and B and subjected to axial loads P and F along its length applied in the directions shown LAB 6m, LBC-3m A B F If the value of P is 23kN and that of F is 13kN, determine the stress acting in member AB, identifying a compressive stress ( in N/mm2) as negative and tensile stress as positive. Present your answer to three decimal places.
A stepped shaft has the appearance shown in Fig 5-13. The region AB is aluminum, having G= 28 GPa, and the region BC Is steel, having G- 84 GPa. The aluminum portion is of solid circular cross section 45 mm in diameter, and the steel region is circular with 60 mm outside diameter and 30-mm inside diameter Determne the maximum shearing stress in the aluminium in MPa if a torsional load ot 4000 N m is applied at B. Ends A and Carerigidly damped. 45 mm 60 mm 30 mm 12m
Find the maximum tensile and compressive normal stresses in the beam below. Mark their locations along the height of the cross section and along the length of the beam. (Note: The centroid is located 4.423in from the top of the cross section and I= 42.0 in*.) W= 1k/ft 6k 10' 5' 4423" 8.75 M (k-t) -12.5 Cross section
13
PLEASE DRAW THE FBD. DO NOT COPY YOUR ANSWER FROM OTHER. I WANT TO SEE THE FBD OF INDIVIDUAL DEFORMATIONS ON HOW YOU WILL ARRIVE ON YOUR ANSWER. DRAW FBD ON EACH PLEASE. NOT ONLY ONE FBD
17