Fig. 2 shows an example of power system protection system divided into several sections. In a case where fault occurred at P (marked in the figure), list down the circuit breaker/s that will act as the primary protection system and the backup protection system. RL-5 RL-6 平 P L67 C7 B4 G11 C1 82 L89 Generator Transformer Line Protection Protection Protection B3 RB RL-8 RL-9 Bus Protection Fig. 2

Fig. 2 shows an example of power system protection system divided into several sections. In a case where fault occurred at P (marked in the figure), list down the circuit breaker/s that will act as the primary protection system and the backup protection system. RL-5 RL-6 平 P L67 C7 B4 G11 C1 82 L89 Generator Transformer Line Protection Protection Protection B3 RB RL-8 RL-9 Bus Protection Fig. 2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Refer to figure 2. Calculate fault current
don't copy
The following values were seen in the measurements made separately by the primary and secondary of a 220/270 V phase transformer. R1 = 4 ohms, X1 = 4.6 ohms, R2 = 0.89 ohms, X2 = 1.79 ohms; R2T = 8.7 ohms, X2T = 8.8 ohms (total values measured on the secondary side), Xm = 60 ohms, Rfe = 750 ohms, (using a T-type equivalent circuit) a.) Primary and secondary currents and their phase angles b.) Active and reactive powers drawn by the transformer from the network. please solve them all, thanks..
c) Figure 4 (c) shows two (2) 11 kV/415V distribution transformers are connected using 2 incomings with sectionalizing breakers at HV and LV side. briefly summarize the switching procedure for maintenance personnel to shutdown the Transformer 2 for breaker servicing work at LV side and put back in-service. Supply line 1 Supply line 2 Disconnect switch Disconnect switch HV side breaker HV side breaker HV sectionilizing breaker HV busleection 1 HV bus section 2 Transformer 1 Transtormer 2 Indoor switchgear LV side breaker LV sectionilizing breaker LV bus section 1 LV bus section 2 Feeders breakers Outcoming feeders Figure 4 (c)
X= 0 Y = 6 Can you please help me with parts 1,2 and 3 of this question
a) In Three Phase Faults that will occur separately on A, B, C and D Busbars, Calculate the currents. b) Maximum fault currents to pass through KA, KB, KC1, KC and KD Protection devices determine. Help me please... Thank you so much.
1. A Zone 2 fault is detected in 25 cycles of a 60 Hz power system and the circuit breaker clears in 5 cycles. Calculate the fault clearing time for this case. a) 60 ms b) 500 ms c) 120 ms d) 150 ms 2. The Burden on a CT should always be kept a) High b) Low c) Either, because burden does not affect the CT d) At the rated burden value for the CT 3. The purpose of backup protection is a) To increase speed b) To leave no blind spots c) To guard against failure of primary d) To increase reach 4. In distance protection scheme, which Zone is set to trip instantaneous without any delay? a) Zone 3 b) Zone 2 c) Zone 1 d) All of the above 5. The protective relay is provided to: 1) Provide additional safety by limiting arcing current during circuit breaker operation. 2) Close the contacts when the actuating quantity attains a certain predetermined value. a) Only 1 b) Only 2 c) Both 1 and 2 d) None of these
The copper loss and iron loss of transformer at full load are 3600W and 500 W respectively. The copper loss and iron loss at 25% of full load will be respectively 1-(3600 W and 1000 W) 2-(1800 W and 500W) 3-(1800 W and 1000W) 4-(225W and 500 W)
Which of the following is not a boundary condition for an SLG fault on phase 'a' of a power system?
pls solve it before 10 min