F14-6. The 5-lb collar is pulled by a cord that passesaround a small peg at C. If the cord is subjected to a constantforce of F = 10 lb, and the collar is at rest when it is at A,determine its speed when it reaches B. Neglect friction.- 4 ftB3 ftF = 10 lb

The given figure is shown below:

Answered: F14-6. The 5-lb collar is pulled by a…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The gear-pulling assembly shown consists of a crosshead CF, two grip arms ABC and FGH, two links BD and EG, and a threaded center rod JK. Knowing that the center rod JK must exert a 4800-N force on the vertical shaft KL in order to start the removal of the gear, determine all forces acting on grip arm ABC. Assume that the rounded ends of the crosshead are smooth and exert horizontal forces only on the grip arms. 80 mm 60 mm 80 mm E 150 mm B 250 mm K A |H 95 mm Flg. P6.144
(a) The uniform 50 lb beam is supported by the rope that is attached to the end ofthe beam, wraps over the pulley, and is then connected to the 100 lb block. If thecoefficient of static friction between the beam and the block is µs=0.4, determinethe maximum distance that the block can be placed from A and still remain inequilibrium. Assume that the block will not tip.(b) The pulley connecting the block to the uniform beam is replaced by a rough peg.The coefficient of static friction between the peg and the rope is µs = 0.4 also.Determine the revised maximum distance that the block can be placed from Aand still remain in equilibrium.
A 200 Ib weight is suspended as shown. Wires DE and BC (Ewire = 29,000 ksi) have a 0.05" diameter. Bar DA is rigid and A is a pin connection. Determine the downward motion of the weight when it is attached to the cable at Cand released. The wires are straight and the rigid bar DA is horizontal before the weight is attached. 3ft 4 f
F8-5. Determine the maximum force P that can be applied without causing movement of the 250-lb crate that has a center of gravity at G. The coefficient of static friction at the floor is us 0.4. = Prob. F8-4 P- 4.5 ft 1.5 ft 1.5 ft Prob. F8-5 2.5 ft 3.5 ft
Calculate the rod forces in the truss system in the figure. Specify the pressure-pull conditions.
Calculate the beam moments at each beam shears.
8K A W K 18'-0" B 12K 6'-0" 2b. Support A is a pin; support B is a roller. If the vertical reaction at A is 8K, what is the magnitude of the distributed load, w, (in kips per foot)?
Replace the loading by an equivalent resultant force and couple moment acting at point A.
3/99 SS The uniform 15-kg plate is welded to the ver- tical shaft, which is supported by bearings A and B. Cal- culate the magnitude of the force supported by bearing B during application of the 120-N-m couple to the shaft. The cable from C to D prevents the plate and shaft from turning, and the weight of the assembly is carried en- tirely by bearing A. 200 mm 120 N·m A B 200 mm PROBLEM 3/99 80 mm 600 mm D 400 mm
A continuous beam has a loading shown. Assuming constant flexural rigidity (EI). 8KN 2m 2m 5kN 6kN/m 4kN/m B 2 TAT C D 37 1m 4m 6m Determine the following: a. Moment at 1 or B (kN-m; write positive or negative) b. Moment at 2 or C (kN-m; write positive or negative) c. Reaction at 1 or B (kN; positive value only) d. Reaction at 2 or C (kN; positive value only) e. Reaction at 3 or D (kN; positive value only)
The 9.8-lb force is applied at point A of the crank assembly. Determine the moment of this force about point 0. F = 9.8 lb 34 A 0.90" -y 2.75"
Note:hand written solution should ne avoided.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

F14-6. The 5-lb collar is pulled by a cord that passes around a small peg at C. If the cord is subjected to a constant force of F = 10 lb, and the collar is at rest when it is at A, determine its speed when it reaches B. Neglect friction. - 4 ft B 3 ft F = 10 lb