F = 650 N F2 = 750 N 00 45 F = 900 N Probs. 2–36/37

Q: A tower guy wire is anchored by means of a bolt at A. The tension in the wire is 4000 N. Determine…

A: To determine the direction cosine angles for a given force in 3-D.   From the given figure,…

Q: M kN-m ソー16m。 M= 1000 kN -m d: 36 ° y Find: T= Nオ kN Ax ニ A Ay: EN る の

A:

Q: Determine degree of static indeterminacy

A:

Q: The rigid bars shown are separated by a roller at C and pinned at A and D. A steel rod at at B helps…

A:

Q: eta = 30 degree T = 6kN   Find the magnitude of the resultant forces acting on the eyebolt.

A: Rx=Tsinθ+8cos45Ry=Tcosθ-8sin45Rx=6sin(30)+8cos45Ry=6cos(30)-8sin45Rx=8.65685kNRy=-0.4607

Q: two wires are 492 mm² for AB and 214 mm² for AC. Wire AB is inclined 27-degrees with the horizontal…

A:

Q: determine the force developed in each cross section.

A: Detailed solution below . Hope it will help you. Good luck.

Q: A force pair M is applied on a plane that makes an angle with the vertical to the beam of which…

A: Question is based on the vertical beam cross section . Moment on beam and dimensions on beam are…

Q: 000 2-46. Determine the x and y components of each force acting on the gusset plate of the bridge…

A:

Q: 180.0 40.601 7. One grid line = 1 foot. 2. Draw the arrows and label the reaction forces. Label the…

A:

Q: about points and g he to1ce C1500#) opplies at tuss ro- use VARIGNONS THEOPEM Determine the oment…

A:

Q: Determine the resultant moment of forces about the point O? Neglect the beam thickness *KN 15m #2kN…

A:

Q: The wire AB is unstrentched when tetha = 45 degrees. If a load is applied to the bar AC, which…

A:

Q: 100-lb.homogeneous plate is supported by a ball joint at A, a simple bearing at B, and a cable at C.…

A: Given:- W=100lb Vertical  force=120lb To find:- Force

Q: Qg: If the weightless half- cylindrical gate, show in figure below, is in equilibrium, what is the…

A:

Q: 530 N 310 285 310 mm mm mm 325 mm 550 mm 325 mm

A: Consider the given figure. The vertical reaction at point B is By. The horizontal reaction at point…

Q: Question Bank - Friction The two homogeneous bars AB and BC are connected with a pin at B and placed…

A:

Q: 5- Replace the given forces by an equivalent resultant force and a couple moment at point P. [In…

A:

Q: What is degree of static indeterminacy of the frame? * (3 Points) 27 kN+ 21 F 5 m 54 kN - C 21 D 5 m…

A: Given:-  To find:- degree of static indeterminacy of given structure

Q: The frame shown in the figure is supported by a hinge at A and a roller at E. Compute the horizontal…

A:

Q: O 300 mm 30° 30° A P 300 mm B The two wires are connected togetherat A. If the force P causes point…

A: Determine normal strain developed in each wire

Q: Replace the loading on the frame by a single resultant force. Suppose that F= 600 N, a = 0.6 m, and…

A: Given : F = 6600 N a = 0.6 m h = 1.1m To Find :

Q: D 4 m

A:

Q: For the given cross section, determine the torsional and warping constant with the given parameters.…

A: Solution: The bending resistance formula is given by the equation:  θ=TL/GJ where  T = Torque (N·m…

Q: The uniform rectangular panel ABCD has a mass of 40 kg and is hinged at its corners A and B to the…

A:

Q: QI-The homogeneous bar ABCD shown in the Figure is supported by a cable that runs from A to B around…

A: As per guidelines we need to answer only first question so please repost rest question separately.

Q: displacemen steel member has a cross-sectional area of 300 mm². Use the method of virtual work

A:

Q: Determine degree of static indeterminacy

A: Given data : Number of external support reaction (R)=1+2=3 Number of member (m)=6 Number of joint…

Q: (Mc)y = -226 N-m The shaft is supported at its ends by two bearings A and B and is subjected to the…

A:

Q: The lower ends of the three steel bars in Figure are at the same level before the applied…

A:

Q: H.W. Determine the horizontal and vertical comporents of force at pins A and D. 03n 12 KN

A: To find reactions at A and D

Q: Given v, = 25m/s %3D S.g.= 0.83 Find the force required plate d=somm jet

A: given :-

Q: D 200 mm 300 mm -400 mm- A C When force P is applied to the rigid arm ABC, point B displaces…

A:

Q: The crowbar is subjected to a vertical force of P = 27 Ibat the grip, whereas it takes a force of F…

A: Given : P = 27 lb at the grip and F = 160 lb at the claw To Find : Moment of force P about A Moment…

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.