Explore the effect of insulation thickness on the heat loss q and the temperature of the insulation outer surface T2 for a steam pipe of 0.05-m outside diameter that is insulated with a layer of calcium silicate. The temperature of the steam fixed at 600 K and the outer surface is exposed to an airflow (T=30°C) that maintains a heat transfer coefficient of h = 85 W/m².K, which includes the effects of radiation. where r,= 0.025 m and r2 is a variable (0.025 < r2 < 0.50 m). Compute and plot the heat loss and outer surface temperature Ts,2 as a function of the insulation thickness.

Explore the effect of insulation thickness on the heat loss q and the temperature of the insulation outer surface T2 for a steam pipe of 0.05-m outside diameter that is insulated with a layer of calcium silicate. The temperature of the steam fixed at 600 K and the outer surface is exposed to an airflow (T=30°C) that maintains a heat transfer coefficient of h = 85 W/m².K, which includes the effects of radiation. where r,= 0.025 m and r2 is a variable (0.025 < r2 < 0.50 m). Compute and plot the heat loss and outer surface temperature Ts,2 as a function of the insulation thickness.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: h = 30 W/m²K Taj = 20°C h. = 60 W/m²K Tzo =-15°C Fiberglass L=10 cm Plaster board Plywood L=2 cm…

Q: A heater coil is completely immersed in an oil bath that is insulated on all sides except for the…

A: a) Here's a schematic of the system: Heat transfer rates: Heat transfer from the coil to the…

Q: Thermal treatment of a steel cube, of 10 cm side length, L, requires a two step cooling process. In…

A: Given that, Length of cube, L=10 cm,Temperature of cube, Ti=500 °C,Cooling temperature of cube,…

Q: The thermal conductivity of a sheet of rigid, extruded insulation is reported to be k = 0.029 W/m-K.…

Q: A 50-meter-long cast iron pipe with a 10-centimeter outside diameter goes through a 288 K…

Q: To increase the rate of heat transfer from a device, which has 0.1 m² of exposed surface, you added…

A: Write the given data. As1=0.1 m2n=500L=4 cmd=2 mmh=42 W/m2kk=240 W/mK

Q: An isolating wall (made up of 2-10mm thick plywood with 5mm woven silica sheet in between) encloses…

A: Given:Thickness of 1st plywood, t1=2 mmThickness of the silica sheet, t=5 mmThickness of 2nd…

Q: A silicon computer chip (k = 150 W/m · K) is attached to the top of a motherboard tha generating…

Q: A very thin silicon chip is bonded to a 6-mm thick aluminum substrate by a 0.02-mm thick epoxy glue.…

Q: Steam at a temperature of 300 °C flows through a steal pipe, k = 14.9 W/m.K of 60 mm inside diameter…

A: In general, there are three modes by which heat gets transferred from one place to another. The…

Q: Explore the effect of insulation thickness on the heat loss q and the temperature of the nsulation…

A: The problem can be sketched as follows,

Q: two 5 cm diameter, 15 cm long aluminum bars (k=176W/m(degrees Celsius)) with ground surfaces are…

Q: An isothermal sphere 3 cm in diameter at 80°C is embedded in a large clay region. The temperature of…

A: Disclaimer: “Since you have asked multiple questions, we will solve the first question for you i.e…

Q: 3. Hot water flows inside a 2.5 cm inner diameter tube, the tube has a wall thickness of 0.8 mm…

A: Given: Inner radius = 2.5 cm Thickness = 0.8 mm And 3 thermal resistances Correct answer: A 9.94…

Q: An electric wire, with 2 mm in diameter, is insulated by a rubberized liner (k = 0.13 W/m.K) of 2 mm…

Q: A temperature sensor may be modeled as a sphere having a thermal conductivity of 91 W/m-K, a density…

Q: calculate the heat transfer rate per unit length of a cylindrical wall of inner and outer radius as…

A: It is given in the data that inner radius is r1=0.1 m and outer radius is r2=0.2 m. Thermal…

Q: A wall made of concrete 0.305 m thick is insulated on the sides. Uniform wall temperature 10°C (283…

A: Given: The thickness of concrete wall, L = 0.305 m The temperature of wall, Ti = 283.2 K The…

Q: Example 1 A 15 mm diameter and 5 m long electric wire is tightly wrapped with 2 mm thick plastic…

Q: To increase the rate of heat transfer from a device, which has 0.1 m² of exposed surface, you added…

A: Given data: Area of exposed surface = A = 0.1 m2 Length of fin = l = 4 cm = 0.04 m Diameter of fin =…

Q: Determine heat loss of the brick wall.

A: Given, Brick wall,k= 0.9 W/mkThickness,t= 0.18 mTo=-50C=273-5=268 KTin=270C=27+273=300 KHeat…

Q: An electronic component, 65 mmx65 mm, in steady state operation reaches the base temperature of…

Q: Water flows at 67 C inside a 2.5 cm inside diameter tube such that hi = 3500 W/m² .C. The tube has a…

Q: 1. Find the rate of heat leakage for a spherical tank 2 m inside diameter and 12 mm thick with…

Q: An isolating wall (made up of 2-10mm thick plywood with 5mm woven silica sheet in between) encloses…

A: Heat transfer Heat transfer is the process in which heat is transfer from hot body to cold body or…

Q: A room is well insulated apart from a single-glazed window measuring 1 m2 and 4 mm thick. The…

A: To find: The convective heat transfer coefficient for outside hout. Given : The Area is A=1 m2.…

Q: The oven of a stove must have a sufficient insulation so that the surface temperature of the stove…

A: For solution refer below images.

Q: (2) The pipeline made of steel tube with a diameter of 150x5mm, should be covered with two layers of…

A: The mathematical formula for the thermal resistance per unit length of a hollow cylinder is given as…

Q: Window height (0.8 m) and width (1.5 m) consisting of two layers of glass (k = 0.78 W /m Co)…

Q: Q1 A composite house wall is constructed from 1.2 cm layer of fiber insulating board, an 8.0 cm…

A: Given Data

Q: A furnace wall comprises three layers of thickness 250 mm, 100 mm, and 150 mm with thermal…

Q: Steel pipe (outer diameter 100 mm) is covered with two layers of insulation. The inner layer, 40 mm…

A: Given data: The diameter of the steel pipe, d = 100 mm. The thickness of the inner insulation, t1 =…

Q: . Saturated steam at 500 K flows in a 0.20 m inside diameter, 0.21 m outside diameter pipe. The pipe…

Q: Pressurized steam flows through a pipe of 0.6 m diameter. The pipe is embedded in a concrete block…

A: Given: Surface Temperature of the concrete square block (T2)=301KSurface Temperature of the pipe…

Q: Estimate the unit thermal resistance for a vertical 1.5 in. (40 mm) air space. The air space is near…

A: Write the given data. Type of air space-1.5 in (40 mm) verticalT0=10 °F (-12 °C)

Question

Explore the effect of insulation thickness on the heat loss q and the temperature
of the insulation outer surface T2 for a steam pipe of 0.05-m outside diameter
that is insulated with a layer of calcium silicate. The temperature of the steam
fixed at 600 K and the outer surface is exposed to an airflow (T=30°C) that
maintains a heat transfer coefficient of h = 85 W/m².K, which includes the effects
of radiation. where r,= 0.025 m and r2 is a variable (0.025 < r2 < 0.50 m).
Compute and plot the heat loss and outer surface temperature Ts,2 as a
function of the insulation thickness.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 9 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q2/ A plane wall (K =17 W/m.°C ) with (60 mm) thick. Both sides of the wall are insulated with ( 2 cm) layer of insulating material having (K=0.22 W/m.°C ) The heat transfer coefficient, considering convection on both sides of wall are ( 120 and 10 W/m.°C ) respectively. Calculate the heat transfer per unit area if the temperature difference across the wall is (90 °C).
What is the temparature at depth 1 cm from the surface at t=2 minutes after the start of the coolıng ?
Heat transfer
A pipe of diameter 400 mm carries water at a velocity of 25 m/s. The pressures at the points A and B are given as 29.43 N/cm2 and 22.563 N/cm2 respectively while the datum head at A and B are 28m and 30 m. Find the loss of head between A and B. Sketch the arrangement.
Please quick answer
Please fats. The answer in the box is incorrect
We have a wall (k = 10 W/mK) with a thickness of 0.4 m. At a certain instance of time temperature distribution is given by T(x) = 50 x²– 450 x + 350. a- Please calculate the rate of heat transfers entering and leaving the wall for a unit surface area and also find the change in the energy storage of the wall. b- If the environment temperature is 85 °C, what is the convection coefficient between the cold surface of the wall and environment.
***answer is correct
A cylindrical shape body of length is 1.9 m and diameter is 400 mm is inside a room where the ambient temperature is equal to 300 K. The initial temperature of the body is equal to 350 K. If the heat convective coefficient is equal to 1.3 W/m^2.K. What is the thermal conductivity K.
Homework problem for unsteady-state heat transfer Consider a product to be sterilized if its coldest location during heating reaches 115°C. Consider sterilization of potatoes where potatoes (4 cm diameter) is heated in steam at 121°C. Assume symmetrical heating of potatoes and the heat transfer coefficient between the steam and the potatoes is 20 W/m² K. The thermal diffusivity for potatoes is 1.5 × 107m²/s and the thermal conductivity is 0.4 W/m K. The potatoes are initially at 30°C. 1) Calculate the heating time needed for sterilization. 2) Calculate the temperature at the center of the potato after heating 1000 s and 2000 s. Plot how the temperature at the center changes with time t. 3) Calculate the temperature at the surface of the potato at 2000 s. Qualitatively plot how the temperature changes across the apple at t = 2000 s.
Ton
PLEASE ANSWER WITH UNIT!!!!! A copper sphere having a diameter of 2 cm is initially at a uniform temperature of 312 F. It is then suddenly exposed to an air-forced- convection environment at 20 C of which the convective heat transfer coefficient is 200 W/m2K. Embedded in the sphere is a thermocouple to measure the temperature as a function of time. How long will it take for the thermocouple to indicate 30 C. What is the time constant for this system? (Density of copper is 8890 kg/m3) , (Specific heat for copper is 398 J/kg.K).