Answered: explain | bartleby

Related questions

Question

Briefly explain the function of the following as used in mobile telephone
networks
i) cell, ii) Base transceiver station (BTS), iii) Public switch telephone network
(PSTN)

Expert Solution

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

Please write out all steps and draw diagrams/sketches as needed along with using the units thoroughly. Thanks!
QUESTION 20 In a DC circuit with a single resistor, a current of 13 Amperes flows through a point in the circuit. After a time of 10 minutes, which of these expressions yields how much charge has flowed through the point in this time in SI units? a. 13 divided by 10 b. 13 times 600 c. 13 times 10
Vocabulary Series: Items are all on one loop connected to the sides of the power source (battery) Parallel: items are on separate loops connected to the sides of the power source (battery) 1. Draw a circuit with a bulb, switch, and single cell, connected with wire. 2. Draw a circuit with 2 bulbs in series with a resistor, a switch, and a 2 cell battery connected with wire. 3. Draw a circuit with a buzzer and a light bulb in parallel with 2 switches and one 2 cell battery connected with wires. 4. Draw a circuit with 10 light bulbs in series with a switch and an AC power source connected with wires. 5. Draw a circuit with a motor, a switch, and two 2-cell batteries in series connected with wires.
Q1 : Why the sum of all currents at any junction is zero Q2 : Why the sum of all vlotages across any loop is zero Q3 : If you connect a voltmeter across the power supply what will be its reading if (a)the circuit is open, (b) the the circuit is closed, and why ?
In the circuit below (See Figure 5), the capacitor C is initially uncharged and switch S is closed at time t=0. a) Find the current I just after the switch S is closed. b) Find the current I at time t=. c) Find the potential difference across the capacitor and determine which late, upper or lower, is at higher potential at time t=-.
3) Consider the simple Direct-Current (DC) circuit shown below. The purpose of this problem is to reinforce the concepts of how to analyze circuits, i.e., to conduct circuit analysis. Show all work. V = 12.0 V 3R=352 Label the circuit completely: i) Calculate the magnitude of the total current in the circuit, and then label the current magnitude and direction in the circuit diagram above; ii) Show the polarity of the power supply, in the diagram; ii) Show polarity of the voltage drop across the R = 3 Ohm resistor; and iv) Calculate the magnitude of the voltage drop across the R = 3 Ohm resistor, in Volts (V).
Record two peak-to-peak time measurement of this oscilloscope. What is the initial time? What is the Final time?
Need Help with #2
3. Fast help needed to answer this Engineeing question. Check image. Please answer all parts Postive feedback for right answer :)
Maya Aðun- Circuits Lab Simulation - 10382745 ☆ @ Fle Edit Vlew Insert Format Tools Add-ons Help Last edit was made 6 minutes ago by Zainab Chebib Shar 100% Normal text Comic San. 12 B U 三三三|三 E - E E E ..1. .I. 2 I 3 4 I ..5. . 6 . 7.. Resistor Switch a. A connecting used to form a complete path for the current. b. A voltage source such as a C. A source of resistance such as a or 2. Answer the following based on the figures below: A B a. Figure A is an example of a circuit because it provides only one pathway for charges to flow. b. Figure B is an example of a circuit because it provides more than one pathway for charges to flow. MacBook Pro
1. Explain how does one ensures that logic gates X and Y are compatible. 2. Predict and explain the state of LEDs W, Z, and the buzzer duringa) Current sourcingb) Current sinking
PART II Truth Tables and Logic Gate Design 6. Create a truth table for the following combination logic gates: a. A B A B 0 b. D output