Experiments have been conducted on a metallic cylinder 12.7 mm in diameter and 94 mmlong. The cylinder is heated internally by an electrical heater and is subjected to a crossflow of air in a low-speed wind tunnel. Under a specific set of operating conditions forwhich the upstream air velocity and temperature were maintained at V = 10 m/s and26.2°C, respectively, the heater power dissipation was measured to be P = 46 W, while theaverage cylinder surface temperature was determined to be T, = 128.4°C. It is estimatedthat 15% of the power dissipation is lost through the cumulative effect of surface radiationand conduction through the endpieces.Thermocouple for measuringairstream temperaturePitot tube fordetermining velocityWindtunnelPower leadsto electrical heaterHeatedcylinderInsulatedendpieceThermocoupleleads1. Determine the convection heat transfer coefficient from the experimental observations.2. Compare the experimental result with the convection coefficient computed from anappropriate correlation.

The average surface temperature is Ts=128.4°C The temperature of the air is Ta=26.2°C The velocity…

Experiments have been conducted on a metallic cylinder 12.7 mm in diameter and 94 mm long. The cylinder is heated internally by an electrical heater and is subjected to a cross flow of air in a low-speed wind tunnel. Under a specific set of operating conditions for which the upstream air velocity and temperature were maintained at V = 10 m/s and 26.2°C, respectively, the heater power dissipation was measured to be P = 46 W, while the average cylinder surface temperature was determined to be T, that 15% of the power dissipation is lost through the cumulative and conduction through the endpieces. 1 128.4°C. It is estimated effect of surface radiation Thermocouple for measuring airstream temperature Pitot tube for determining velocity -Wind tunnel Power leads to electrical heater Heated cylinder Insulated endpiece Thermocouple leads 1. Determine the convection heat transfer coefficient from the experimental observations. 2. Compare the experimental result with the convection coefficient computed from an appropriate correlation.

Experiments have been conducted on a metallic cylinder 12.7 mm in diameter and 94 mm long. The cylinder is heated internally by an electrical heater and is subjected to a cross flow of air in a low-speed wind tunnel. Under a specific set of operating conditions for which the upstream air velocity and temperature were maintained at V = 10 m/s and 26.2°C, respectively, the heater power dissipation was measured to be P = 46 W, while the average cylinder surface temperature was determined to be T, that 15% of the power dissipation is lost through the cumulative and conduction through the endpieces. 1 128.4°C. It is estimated effect of surface radiation Thermocouple for measuring airstream temperature Pitot tube for determining velocity -Wind tunnel Power leads to electrical heater Heated cylinder Insulated endpiece Thermocouple leads 1. Determine the convection heat transfer coefficient from the experimental observations. 2. Compare the experimental result with the convection coefficient computed from an appropriate correlation.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Metal plates of size 60 cm × 50 cm, and thickness 1 cm are initially at 100◦C. They are to be cooled by blowing chilled air at 2 m/sec over both surfaces, the flow being directed along the side whose length is 60 cm. Incoming air temperature is 10◦C. Data for the metal: ρ = 7854 kg/m3, cp = 434 J/kg/K, k = 60.5 W/m/K Data for air: Use values at 50◦C. (a Determine the convective heat transfer coefficient at the surfaces of the plates.(b Determine whether lumped system analysis is applicable(c Assume the convection coefficient is constant, determine how much time is necessary for the temperature of the plates to drop to 25◦C.(d Estimate the total heat lost by a plate when it has reached 25◦C.
! Required information Air flows in a pipe under fully developed conditions with an average velocity of 1.25 m/s and a temperature of 24°C. The pipe's inner diameter is 4 cm, and its length is 4 m. The first half of the pipe is kept at a constant wall temperature of 100°C. The second half of the pipe is subjected to a constant heat flux of 200 W. The properties of air at 80°C are p = 0.9994 kg/m³, k = 0.02953 W/m-K, v= 2.097 x 10-5 m²/s, cp=1008 J/kg-K, and Pr = 0.7154. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Air 1.25 m/s 2m T, = 100°C D = 4 cm 2 m Q₁ = 200 W a) Determine the air temperature at the 2 m length. The air temperature at the 2 m length is b) Determine the air temperature at the exit. The air temperature at the exit is °C. c) Determine the total heat transfer to the air. The total heat transfer to the air is W.
A pipe 30 m long with an outer diameter of 75 mm is used to deliver steam at a rate of 1500 kg / hour. The vapor pressure is 198.53 kPa entering the pipe with a quality of 98%. The pipe needs to be insulated with a thermal conductivity of 0.2 W / (m K) so that the quality of the steam will only slightly decrease to 95%. The outer surface temperature of the insulation is assumed to be 25 ° C. Ignore resistance conductive of the pipe material and it is assumed that there is no pressure drop in the pipe. a. Determine the enthalpy of incoming vapor = Answer kJ / kg. b. Determine the enthalpy of steam coming out = Answer kJ / kg. c. Determine the vapor heat change / loss along the flow = Answer watt. d. Specify the minimum required insulation thickness = Answer cm.
Solve this problem And please provide Handwritten answer
e
6-34 Liquid ammonia at 10°C and 1 atm flows across a horizontal cylinder at a velocity of 5 m/s. The cylinder has a diameter of 2.5 cm and length of 125 cm and is maintained at a temperature of 30°C. Calculate the heat lost by the cylinder. 6-65 Water flows over a 3-mm-diameter sphere at 5 m/s. The free- stream temperature is 38°C, and the sphere is maintained at 93°C. Calculate the heat-transfer rate. 6-95 A tube bank consists of a square array of 144 tubes arranged in an in-line position. The tubes have a diameter of 1.5 cm and length of 1.0 m; the center-to-center tube spacing is 2.0 cm. If the surface temperature of the tubes is maintained at 350 K and air enters the tube bank at 1 atm, 300 K, and u∞ = 6 m/s, calculate the total heat lost by the tubes.
Air at 20 °C blows over a hot plate 50 by 75 cm maintained at 250 °C. The convection heat-transfer coefficient is 30 W/m2·K. Find:Calculate the convective heat transfer rate.Assuming that the plate is made of carbon steel (1% C) 2 cm thick and that additional 300 W is lost from the plate surface by radiation besides convection heat transfer, calculate the plate temperature on the other side.(Note: the thermal conductivity of carbon steel (1% C) is about 43 W/m·K)
Hot water is flowing though the center of a AISI 304 stainless steel pipe with a diameter of 300mm, a wall thickness of 10mm and a length of 5m. The pipe is coated with a 2.5mm thick layer of Teflon and covered with a 30mm thick layer of insulation. The water is flowing at a velocity of 0.0015 m/s. Assume the velocity profile to be fully developed. The water is at a temperature of 92°C and the air surrounding the pipe is at 22°C. Some transport properties and dimensions are shown in the table below. 1. What is the heat transfer rate through the pipe and insulation? 2. What is the heat flux at the inner pipe surface and the outer surface of the insulation? 3. What is the temperature of the outer surface of the insulation? Insulation Pipe Too water Uwater Teflon Tm air hair Pipe inner diameter: 300mm Pipe wall thickness: 10mm Teflon Layer thickness: 2.5mm Insulation thickness: 30mm Length: 5m To, water: 92°C Lair: 22°C hair: 75 W/m2/K k30455: 15.2 W/m/K kTeflon: 0.38 W/m/K kinsulation:…
B7
Hot air flows with a mass flow rate m = 0.09 kg/s through an uninsulated sheet metal duct of diameter D = 0.15 m, which is in the crawlspace of a house. The hot air enters at 110°C and, after a distance of L 5 m, cools to 80°C. The heat transfer coefficient between the duct surface and the ambient air at To 0°C is known to be h, = 9 W / m²K. (a) Calculate the heat loss from the duct over the length L. (b) Determine the heat flux and the surface temperature at x = L. (c) Determine the heat flux and the surface temperature at x = 0. Assume, for air at Tm 368 K: c, 1011 J/kg.K; for air at Tm.L = 353 K: k= 0.030 W/m.K, u = 209x10' N.s/m2, Pr = 0.70%; for air at Tm,0 = 383 K: k = 0.033 W/m.K, u=223x10" N.s/m2, Pr = 0.69. Show all calculations. Cold Air Hot air in -L-
Parvinbhai
What is the length of tubing required to cool air from 80°C to 20°C via an isothermal tube maintained at 0°C? The tube diameter is 20 cm. Mean velocity of air is 4 m/s. Assume the flow to be fully-developed.