Exercise 2: Quality control of bricks in a factory In a brick factory, quality control is carried out according to four criteria: weight P, length L, width M and height H (0 incorrect, 1 correct). This allows the bricks to be classified into three categories: • QUALITY A the weight P and at least two dimensions are correct QUALITY B the weight alone is incorrect or, the weight being correct, at least two dimensions are incorrect. QUALITY C: the weight P is incorrect as well as one or more dimensions. 1. Write the equations of the functions A, B, C. ●

Exercise 2: Quality control of bricks in a factory In a brick factory, quality control is carried out according to four criteria: weight P, length L, width M and height H (0 incorrect, 1 correct). This allows the bricks to be classified into three categories: • QUALITY A the weight P and at least two dimensions are correct QUALITY B the weight alone is incorrect or, the weight being correct, at least two dimensions are incorrect. QUALITY C: the weight P is incorrect as well as one or more dimensions. 1. Write the equations of the functions A, B, C. ●

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1- Select the optimum choice for: high speed air craft skins material. Table 1: The properties of metallic materials E, GPa Max. use lemp, 'C | Density, Mg/cm' ay, MPa | Relative cost per unit sheet area Material 2.8 300 2 Aluminum alloy 200 69 200 7,8 350 350 700 Carbon steel Stainless steel 193 7.8 650 6 8.9 600 6 Nickel alloy Titanium alloy 207 1000 116 600 4.5 900 10 Table 2: Weighting factor Specific yield strength: Max, use temperature: Youngs modulus: 4 2
2.1 Please help. Written on paper not typed on computer or keyboard please. Need help both questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.
Presented below are the quality ratings with regard to soil moisture availability. Erosion rating Moisture rating Erosion Rating MC (%) Rating Slope Slope rating Rating hazard class Low 1 0-5 4 0-5 1 Moderate 2 5-15 3 5-10 2 High 3 15-20 2 10-25 3 Very high 4 >20 1 >25 4 Quality ratings of three land units are tabulated below. Land quality rating Land unit Nutrient availability Trafficability 1 2 1 2 3 1 3 2 2 Additional characteristics of the land units areas follows: Land Permeability Land use M.C. Slope Clay V. Silt OM Structure % % Fine % % unit sand % 1 2 Slow Moderate Rangeland Arable 10 9 40% 10 30 4 blocky 18 8 30% 20 20 2 Coarse granular 3 Moderate to Settled 22 12 20% 15 50 3 Fine rapid granular Suitability Class Nutrient The suitability rating for land qualities for tomatoes and cabbage production is also indicated below; Suitability classes for Tomato production Trafficability Moisture Land Qualities Slope Erosion availability hazard S1 1 2 2 2 2 S2 2 3 3 2 S3 3 4 3 3 4 S4…
can i get help with all parts
1. On the drawing attached, before any geometric controls are applied, what is the coaxility tolerance that is implied between the diameters?
Q2) Answer T for true statements or F for false ones: 1. Intact rock: solid rock sample containing cracks on eye naked. 2. Rock Mass: contains rock samples and crack surfaces on eye naked. 3. The rock sample will break if the applied force is vertical and associated with shear. 4. Unit weight (y) - gm./cm. 5. Void Ratio (e) = Vs/Vv. 6. In point load test if the rock is fresh, ot = 5* I (50) 7. Brazilian Test provides tensile strength values closcr to reality than Point Load Test. 8. Schmidt Hammer Test gives direct values for strength. 9. As more the surface is rough its strength for slipping decreases. 10. Fracture Intercept is the measured distance between irregular fractures
Rank 1-4
Solidworks
answer all parts
Simple Machines-Levers, Inclined Planes, and Pulleys Directions: Use the appropriate equation to answer the following questions. All answers should be recorded below or in your Engineering Design journal. Remember to show all work. A lever has an effort arm that is 5 meters long and a resistance (load) arm that is 3.5 meters long. How much effort is needed to lift a 100 Newton weight? 5K i). Draw the figure representing the problem ii). How much effort is needed to lift a 100 Newton weight? iii). What is the Actual Mechanical Advantage 1. 5m i) AOON 5-5m
44
Do not provide handwritten solution,Maintain accuracy and quality in your answer,Take care of plagiarism,Answer completely,You will get up vote for sure.