Example: For the three hinged arch shown in figure below, find the support reactions and axial force (N), shear force (V), and bending moment (M) at point e It may be noted that, the arch equation is: y(x)=x-0.025x² y(x) a 10m 5m| 60KN d 10m 60KN 10m 60KN e 10m 10m -- X

Example: For the three hinged arch shown in figure below, find the support reactions and axial force (N), shear force (V), and bending moment (M) at point e It may be noted that, the arch equation is: y(x)=x-0.025x² y(x) a 10m 5m| 60KN d 10m 60KN 10m 60KN e 10m 10m -- X

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

c) Using the portal method to calculate and draw the bending moment diagrams for columns AD and BE shown in Figure 4. All members have the same constant EI value. H I 800 kN 3 m D E F 400 kN 3 m A B C 10 m 10 m Figure 4
Please show an complete answer and FBD
Problem 1: The cantilever truss is loaded as shown. All loads are applied normal to the top chord. Use the following values: F = 32 kN as well as A = 2,000 mm? and E = 200,000 MPa for all members. Compute the vertical displacement at point A using Virtual Work Method. Round off your answer to 2 decimal places. F E F F 3 m F = (32 kN) B -2 m D -2 m 2 m
Situation # 3: Assume that the frame in figure C is pin-connected at points A, B, and C, and that joints D and E are fixed-connected, solve the following: 8. Bx (in kN) 9. By (in kN) 10. Cx (in kN) 11. Cy (in kN) 3 k/ft B 6 ft D 1.5 k/ft 10 ft 18 ft -18 ft Figure C E
Determine the mass of the heaviest uniform bar that can be supported in the position shown if the breaking strength of the horizontal cable attached at C is T kN. Neglect friction. A 4 Given: x=1 m $ = 23° T 15.5 kN W = kN (round off to 2 decimal places) B 3.
Q1: The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical forces P = 400 kN and P2 = 360 kN acting at points A and D, respectively (see figure). Bars BE and CF are made of steel (E = 200 GPa) and have cross-sectional areas ABE = 11,100 mm² and Acp = 9,280 mm². The distances between various points on the bars are shown in the figure. Determine the vertical displacements &, and ôp of points A and D, respectively. E1.5m 1.5 m 2.1 m – A P = 400 kN 2.4 m P2 = 360 kN F 0.6 m|
15 kN/m 60 kN C A I B 21 10 m 5 m 5 m Figure no. 8
Given: Waterval catchment (A = 120 km²) shown in Fig. 1. The slope of the watershed is given in Fig. 2. The length of the longest watercourse = 2.5 km Chart Title 100 A = 35% Forest Silty loam A = 40% Farmland Clay 80 60 20 40 A = 25% 20 Pasture о Sandy loam 0 500 1000 1500 2000 2500 3000 Figure 1 Figure 2 2.1. Calculate the slope of the longest watercourse using: (a) Equal Area Method (b) 1085 method 2.2. Calculate the intensity and flood peaks corresponding to a return periods of 10, 50 and 70 years using the following methods: (a) Rational Formula (b) Standard Design Flood (c) Briefly explain the difference between the two methods. Comment the applicability of Rational Formula for the catchment.
A part of slab is given in the figure. The slab is supported by secondary beams AB, CD and EF which are placed with a 50cm spacing. The secondary beams transfer the load they carry to the main beams.In the figure, AE and FB are the visible part of the main beams. Finally, main beams are supported by the columns at both ends. The slab is under uniformly distributed load q=4.5 kN/m2. The span length L is 3,5 m. Determine the dimendions of rectengular cross-sections of timber beams CD and the main beam which has a length of 4 m.
Determine the horizontal component of the force applied by the smooth circular guide on the mass A. mA = 2 kg, y= 100 mm, Vy = 0.6 m/s, ay = -0.2 m/s^2
Learning Goal: A beam with length L = 2.9 m is supported by a pin joint at A and a cable attached at C as shown in (Figure 1). It is subjected to the distributed load with w₁ =1.7 kN/m and w₂ = 2.1 kN/m. The angle between the cable and the beam is 0 = 35°. Determine the normal force, shear force, and bending moment acting at point B, located x = 0.6 m to the left of the end of the beam. D Wi W2 C B L Begin by finding the support reactions for the beam using the free-body diagram shown in (Figure 2). What is the tension in the cable? Express your answer to three significant figures with appropriate units What is the horizontal reaction force at A? Assume the forces acts in the direction shown, and use an appropriate sign. Express your answer to three significant figures with appropriate units. What is the vertical reaction force at A? Express your answer to three significant figures with appropriate units. Now calculate the internal loading at point B using the free-body diagram of…