Example 9.9: Determine the load impedance ZL that maximizes the average power drawn from the circuit of Fig. 9.12. What is the maximum average 42 j5 2 power? 10/0° V -j6 0

Q: 1. Are the theoretical calculations and measured values are equal? Explain?

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Q: fca) = Th 2. 2.

A: See attachment

Q: The amature circuit vesistance of an 18.65kw. 250v series motor is 0.1w. the brush voltage drop is…

A:

Q: A 3-phase, 400v, y-connected induction motor has an equivalent t-circuit consisting of r1=1w, x1=20…

A: Given:r1=1X1=2r2'=1.2X2'=1.5exciting branch impedanceZm=4+j40 All the parameters are per phase…

Q: Calaulate the flux per pole vequired on ful-load for a 50kw. 450v. 8-pole. 600r.p.m Dc Shunt…

A:

Q: Find the no-laad phase and line valtapge of a star- Comected. 4-pole altemator having flux per pole…

A: GIVEN: double layer winding             flux=0.15             slots per pole per phase (m)=4…

Q: At a location in europe it is necesary to supply 300kw of 60hz power. The any Power sources avaiable…

A:

Q: Vending machine. After joining a circuit design company, you are asked to design the control circuit…

A: We need to design the control circuit of a vending machine that sells a type of bottled soft drink.…

Q: Calculate the speed and apen-circuit line and phase voltages of a 4-pole. 3-phase. 60hz star-…

A: In this question,  We need to calculate the speed of the alternator ?  And also find the open…

Q: 2. A TRF receiver is to be designed with a single tuned circuit using a 10µH inductor. The ideal…

A: According to the question,

Q: A combinational switching network, has four inputs (a,b,c,d) and one output. The output is at logic…

A:

Q: Find VDc if VAN = VBN = VCN= 120 volts... Half-wave Three-phase Rectifier Conduction Waveform…

A:

Q: Numerical answer: A 14-bit DAQ device is used to measure a voltage range of +-8 Volts. What is the…

A: For the given Digital to Analog converter specifications the value of resolution needs to be…

Q: No, this question was not a message for somebody on a support team, I literally asked how you solved…

A:

Q: three phase converter has a rating of 600 kW when operating at unity power factor. Neglecting any…

A: We need to find rating at given power factor

Q: When solving the equation why is 1 used rather than 1000? Thank you

A: I will explain you for one part, the same applicable for all the parts

Q: What is the smallest number of poles that can be used in two synchronous machines if it is desired…

A:

Q: DEGREE: ELECTRICAL ENGINEERING  SUBJECT/COURSE: AC CIRCUITS   NOTE: Please solve in this way.  1.…

A: In this question ,balanced delta connected load phase current is given...We have to find out line…

Q: A two-anode mercury-arc rectifier delivers a load of 5.98kw at 115volts.  If the primary of the…

A:

Q: Given: flux per pole = 1,900,000 maxwells; pole pitch = 6.25; gross length of armature core = 10…

A:

Q: A dc Shunt machine has amature and field vEGistances of 0.025w Ond 80w respectively When comected to…

A: In this question we need to find a speed of dc machine when running as motor .

Q: Could you please show the solution step by step without skip any steps for this kind of…

A: For the two subparts of Question 1c given, input x[n] and output y[n] are shown, and they are…

Q: 8. Determine the truth table of the digital circuit shown in the figure below and explain its…

A:

Q: 2. GIVEN. (Include symbols and units) 3. REQUIRED/FIND/MISSING (with symbol/s and units) 4.…

A:

Q: If the L[ eat cos5t] = (s-a)/( s² - bs + 48), determine the value of a.

A: It is given that: Leatcos5t=s-as2-bs+48

Q: A 250v shunt motor giving 14.92kw at 1000r.p.m Takes an armature aurvrent of 75a The amature…

A:

Q: 6) Build an Arduino code that has keypad, LCD display. In this code you are required to: (Void Setup…

A: Final answer with Explanation: 6. Arduino CodeHere's the Arduino code with detailed comments…

Q: The input to a 11-kv, 30, y-connected SYnchronous mator is 60a The effective vesistance Ond…

A: In this question,  Star connected synchronous motor is given.  Find the power supplied by the motor…

Q: DEGREE: ELECTRICAL ENGINEERING  SUBJECT/COURSE: AC MACHINES   NOTE: Please solve in this way.  1.…

A:

Q: The deep wel pump motor is 50hp, 3-phase, 4- poles, 230volts, 60hz induction mator operating at 0.90…

A:

Q: Digital Electronics

A:

Q: An experiment consists of making a A. Not all above B. Expectation value C. Probability 1 D.…

A: An experiment consists of making a  A. Not all above B. Expectation value C. Probability 1 D.…

Q: Computer operations True are affected if voltage unbalance of input is more than 2.5 perecent False

A: Computer operations are affected if voltage unbalance of input is more than 2.5 percent

Q: Number of channels available to a system (company) is 756, cluster size is 9, and number of cells in…

A: Given data, Number of channel N = 756 Cluster size k=9 No of cell C = 108

Q: please solve question number 2,3,4,5

A: Step-2->

Q: Can you please further explain how you used the ID equation to find the solution? Thank you

A: ID=IDSS1-VasVP2from figureIDSS=6.5mAVP=-5Vand Vas=Va-VsVas=0-Vs=-Vsalso ID=VsRs=0.1 Vs mANow put…

Q: n ful-load. develope a useful torque of 162n-r nd it is observed that the rotor electramotive ford…

A: Solution- Ns =120×506= 1000rpmslip speed = 90 rpms=901000 =0.09Nr = 1000-90 =910 rpm Pshaft out =…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.