Example 8: DIY 4■ For the State DiagramShown Below,complete the StateTable on next slide■ Write the inputequations for D Flip-Flops■ Draw the logic diagramExample 8: DIY 4h0000110#10110100101000110111111111Present StateQ2 Q1 QO00000000100101001001101110010010110111000101InputX10101010101010010110100Next StateQ2* Q1* Q0*0010100103132

State diagram is givenAsked to complete state table

Example 8: DIY 4 ■ For the State Diagram Shown Below, complete the State Table on next slide ■ Write the input equations for D Flip- Flops ■ Draw the logic diagram Example 8: DIY 4 1 011 001 101 1 0 0 0 000 0 111 Present State Q2 Q1 Qo 000 000 001 001 010 010 011 011 100 100 101 101 110 110 111 0 0 0 0 Input X 1 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 010 110 100 Next State Q2* Q1*Q0* 001 010 010 31

Example 8: DIY 4 ■ For the State Diagram Shown Below, complete the State Table on next slide ■ Write the input equations for D Flip- Flops ■ Draw the logic diagram Example 8: DIY 4 1 011 001 101 1 0 0 0 000 0 111 Present State Q2 Q1 Qo 000 000 001 001 010 010 011 011 100 100 101 101 110 110 111 0 0 0 0 Input X 1 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 010 110 100 Next State Q2* Q1Q0 001 010 010 31

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the circuit above: what is the input equation for KA?
4 7) For the following sequential circuit: a) Tabulate the state table. b) Derive the state and output equations. c) Re-design the circuit using T flip-flops. Q1 Q -y K, K QP Jo Qo Q Ko K Q clock. please solve it as soon as possible
(b) The state table of a sequential circuit is given in Figure Q1(b). Design the circuit using D FFs by finding the logic expression for the D inputs of the 3 flip flops. Note that the Circuit diagram is not required. State assignment NS/output Q₂ Q₁ Qo PS 0 0 0 A 0 0 B 0 1 0 с 0 1 1 D 1 0 0 E 1 0 1 F Figure Q1(b) X=0 C/1 F/0 E/1 A/1 E/1 B/0 X=1 D/0 A/1 B/1 F/1 C/0 D/1
circuit Show how to implement a 3 input AND gate with a quad 2 input NAND (7400). Draw the Logic diagram for a 3-input AND gate using NAND gates. Truth Table for 3-input AND gate INPUTS B 0 0 1 A 0 0 0 0 1 1 1 1 1 1 C PHON 1 0 0 1 0 1 OUTPUT D
Figure shows a state diagram for a sequential circuit. Design a sequential logic circuit using JK flip-flops with individually controlled JK that implement the state diagram of Figure 3. 0 00 11 1 0 1 0 1 01 10 0
The output X of a logic circuit depends on the input signals A, B and C as in the following logic expression: X = (A + B + C)C (а) Draw the logic diagram using only 2-input gates. Label each gate output. (b) Based on the label in (a), show the calculation for each gate outputs if i. A = 0, B = 0 and C = 0. ii. A = 0, B = 0 and C = 1. (c) Build a truth table for the following input signal combinations by including the output for each gates, according to the label in (a). A В C 1 1 1 1 1 1 1 1 1 1
5. JK flip-flops are often used to build counters. The JK flip-flop will toggle the original output value when triggered by the clock signal if both the J,K inputs are connected with a constant "high"(logic 1). All the JK flip-flops in Figure 2 are negative edge triggered. All the initial values of Q2Q1Q0 are 0. Qo (LSB) (MSB) Input K K Logic 1 Input Q2 000 Figure 2. Counter (a) Sketch the output waveforms forQ2 Q1 Q0. Write down the output binary value (Q2Q1Q0: such as "000", "001") for each clock period on the figure. (b) Describe the function of the counter (e.g. binary down counter counting from 7 to 0).
When signal LD = 0, D1 DO D3 D2 D Q D Q CR CR CR CR CLR LD CLK Q1 QO Q3 Q2 Input C (Clock) at each flip-flop will be following Input CLK (main clock) Input C (Clock) at each flip-flop will always be 1 New data (D3-DO) will enter the flip-flops Current data is retained within the flip-flop
/
Consider the following circuit with 2 inputs (X and Y) and 2 J-K flip flops.· When X=0, the output (Q1Q0) preserves its value regardless of the value of Y.· When X=1 and Y=1, the output (Q1Q0) counts up by one (00-01-10-11-00 …).· When X=1 and Y=0, the output (Q1Q0) counts down by one (00-11-10-01-00 …). a) Derive the state transition, output table.b) Derive flip-flop excitations (logic expressions).c) Draw the circuit implementation using only 2-input NAND gates to drive the inputs J0and K0, and only multiplexers (MUX) to drive the inputs J1 and K1.
11) In Siemens ladder logic, it is acceptable toA) have a functional rung with no coil B) label a coil with the %MB designationC) put two coils in series on one rung D) put a coil on the left side of a rung
Convert the given table into a logic diagram. Upload a photo of your output showing your solution. Decimal Digit 2421 0 0000 1 0001 2 0010 3 0011 4 0100 5 1011 6 1100 7 1101 8 1110 9 1111