Example 3 The triangle frame consists of rods AB and AC.The A=2172mm² and A=2548mm². The external force is F=130kN Determine the displacement of node A. modulus ofelasticity of both rods is E=200GPA, the area of two rod is 2m 300 AN AL A2 Alz

Example 3 The triangle frame consists of rods AB and AC.The A=2172mm² and A=2548mm². The external force is F=130kN Determine the displacement of node A. modulus ofelasticity of both rods is E=200GPA, the area of two rod is 2m 300 AN AL A2 Alz

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Both portions of the rod ABC are made of an aluminum for which E = 70 GPa. 0.4 m 0.5 m B 20-mm diameter 60-mm diameter 3. What is the corresponding displacement at B in millimeter if P = 43 kN and Q = 402 kN? 4
2.54 The rigid bar AB of negligible weight is supported by a pin at 0. When the two steel rods are attached to the ends of the bar, there is a gap A between the lower end of the left rod and its pin support at C. After attachment, the strain in the left rod is 1.5 x 10-3. What is the length of the gap A? The cross-sectional areas are 300 mm? for rod AC and 250 mm² for rod BD. Use E = 200 GPa for steel. A B 0.75 m -1.5 m 2 m FIG. P2.53, P2.54
The truss is subjected to the system of forces as shown in the following figure. The truss is supported by a pin at A and a pin at E. If P1 = P2 = 4 kN, the force in member (CB) is equal to. %3D A 30° 30° OC E D 3 m 3 m P1 P2 Select one: a. 4.618 kN - Tension b. 8 kN - Compression C. 2 kN - Tension d. 8 kN - Tension
The beam is subjected to a shear of V= 2 kN. What is the average shear stress developed in each nail? if the nails are spaced 75 mm apart on each side of the beam. Each nail has a diameter of 4 mm. The N.A is located on 137.5 mm form the bottom of cross section. The second moment of inertia about N.A is 63.5417*10^(-6) m^4. 75 mm 50 mm 75 mm 200 mm 25 mm 200 mm 25 mm 442.62 MPa
The frame shown is supported by fixed support at E and smooth surface at A. Find: • the internal forces exerted by the internal Pin at B. Bx=... By=.. • The internal force at D 600 N 0.4 m B 0.4 m A E -0.3 m- -0.3 m- -0.3 m 3 m- -0.3 m-
The beam shown below is suspended from two steelrods as shown and is initially horizontal. The midpointB of the beam is deflected 15 mm downward byforce Q. The steel used for the rods has properties E= 200 GPa and  = 275 MPa, determinea. the required maximum value of Q.b. the deformation of rod AD.c. the deformation of rod CE.
H.W3: Analysis the structure shown in figure, El is constant W=20 KN/m P =40 KN B C 4m 3 3
Q1: For Fig. (1), a tower guy wire is anchored by means of a bolt at A. The tension in the wire is 2500N. Determine (a)the components F₂, F, and F, of the force acting on the bolt. (b)the angles 0, 0, and 0, defining the direction of the force. Fig (2) if M = 60th in determine the equivalent force-couple system at B. bithen replace this DINA AMACH A TAL MAN - A-au y-axis the Q3: For the three forces shown in Fig. (3), determine the magnitude of the resultant force and its direction 8 measured counterclockwise from the x-axis. Q4: For Fig. (4), determine F. Fy and Ft. Fr. Q5: The rod on the power control mechanism for a business jet is subjected to a force of 80 N as shown in Fig. (5). Determine the moment of this force about the bearing at A. Q6: A 20 N force is applied perpendicular to the handle of the socket wrench as shown in Fig. (6). Determine the magnitude and the coordinate direction angles of the moment created by this force about point O. Q7: Convert: A) 2 km/h to m/s and to…
2. The plate is acted on by four parallel forces, three of which are shown. The fourth force P and its line of action are unknown. The resultant of this force system is the couple-vector. (-1100i + 1500J)lbft. Determine P and its line of action. %D 1400 lb 200 lb 300 1b y 2. ft 3 ft 3 ft 4 ft
Problem 01 The figure shows a truss which is pin connected at C and supported by a roller at D. It carries a vertical loads of 200 kN and 100 kN at joints A and E respectively. State if it is tensile or compressive. 4m D 2m A. E 200 kN 100 kN 6m 3m OCalculate the force in member DE. 2Calculate the force in member BE. 3 Calculate the force in member BC.
A load Pis supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 12200 ksi] rods, and a solid steel [E = 31000 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.72 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.54 in. Assune Ly=59 in and L2=89 in. If all bars are unstressed before the load Pis applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 16 kips is applied. (2) (1) L2 (1) |L1 O B C Answers: i ksi. i ksi.
An axial member consisting of two polymer bars is supported at C as shown. Bar (1) has a cross-sectional area of 680 mm² and an elastic modulus of 29 GPa. Bar (2) has a cross-sectional area of 1580 mm² and an elastic modulus of 15.2 GPa. Determine the deflection of point A relative to support C. 70 KN 0.85 m O -1.902 mm O-2.101 mm O -2.250 mm O-1.354 mm O -2.879 mm 90 kN (1) 90 kN B (2) 1.15 m