EXAMPLE 2.4. In an experiment, a steel specimen of 13 mm diameter was found to elongate 0.2 mm in a 200 mm gauge length when it was subjected to a tensile force of 26.8 kN. If the specimen was tested within the elastic range, what is the value of Young's modulus for the steel snecimen ?

EXAMPLE 2.4. In an experiment, a steel specimen of 13 mm diameter was found to elongate 0.2 mm in a 200 mm gauge length when it was subjected to a tensile force of 26.8 kN. If the specimen was tested within the elastic range, what is the value of Young's modulus for the steel snecimen ?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.2P: A tensile test was performed on a metal specimen having a circular cross section with a diameter of...

See similar textbooks

Related questions

Q: A 19-mm reinforcing steel bar and a gauge length of 75 mm was subjected to ten- sion, with the…

A: Given- gauge length=75mmd=19 mm

Q: A tensile stress is applied along the long axis of a cylindrical steel rod with a diameter of 15 mm.…

A: Using Poisson ratio formula and Young's modulus formula

Q: A bar of a steel alloy that exhibits the stress-strain behavior shown in the Animated Figure 6.22 is…

Q: A round steel alloy bar with a diameter of 19 mm and a gauge length of 76 mm was subjected to…

A: Calculate the stress at different deformation points, σ = LoadCross sectional area Calculate the…

Q: A 2.0 m steel is being subjected into a tensile test. At force 30 kN, the length of the steel is now…

A: Given, Initial length of the steel subject (Li) = 2 m Length of steel after loading (LL) = 2.2 m…

Q: HAMMA A steel bar 100 mm long is subjected to a tensile stress o. If change in length of bar is 0.05…

Q: A tensile stress is applied along the long axis of a cylindrical steel rod with adiameter of 10 mm.…

A: The given data is as follows: Diameter=10 mmChange in diameter=5×10-3 mmModulus of elasticity=200…

Q: Question No.2 Figure P1.16 shows the stress-strain relations of metals A and B during ten- sion…

A: Solution-

Q: Consider a cylindrical specimen of a steel alloy 10.0 mm in diameter and 75 mm long that is pulled…

A: the test is conducted in UTM. the test is standardized by American testing society material . the…

Q: A rod with a length of 1 m and a radius of 20 mm is made of high-strength steel. The rod is…

A: Solution: Given that : Length of rod = 1m = 1000mm Radius of rod = 20 mm Diameter of rod = 40 mm…

Q: Testing a round steel alloy bar with a diameter of 15 mm and a gauge length of 250 mm produced the…

A: Draw the cure with markings:

Q: A tensile test was done on a steel specimen with the gauge length of 525 and a stress of 175 MPa. If…

Q: Question No.2 Figure P1.16 shows the stress-strain relations of metals A and B during ten- sion…

A: It is that point on stress-strain curve, till which stress is linearly varying with strain. As per…

Q: The strain gauge measurement of a steel plate indicate the principle strains are 0.003 and 0.001.…

A: Principle strains- ε1=0.003ε2=0.001E=200 GPaμ=0.33

Q: A specimen of steel has a rectangular cross section 20 mm wide and 40 mm thick, an elastic modulus…

A: solution Given tension P =60000N cross section =20mm×40mmelastic modulus E=207Gpa=207000Mpa…

Q: A tensile stress is applied along the long axis of a cylindrical steel rod with a diameter of 10 mm.…

A: It is required to calculate the strain in the x-direction. Here, is the change in diameter, and do…

Q: Question 4. A tensile test is carried out on a bar of mild steel of diameter 2 cm. The bar yields…

A: Solution: Mild steel bar diameter d =2cm Bar yield under a load Py=80kn…

Q: S Figure P1.16 shows the stress-strain relations of metals A and B during ten- sion tests until…

A: a). Proportional Limit : The proportional limit is the point up to which the stress-strain curve is…

Q: A steel alloy specimen having a rectangular cross section of dimensions 19.1 mm x 3.1 mm (0.7520 in.…

Q: A tensile test specimen of aluminum alloy having a diameter of 0.5 in. and a gage length of 2 in.…

A: Note:- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: 2. The elastic portion of the tension stress-strain diagram for an aluminum alloy is shown in the…

Q: A mild steel specimen originally 300 mm long is pulled in tension with a stress of 500 MPa. If the…

A: Given: Original length of specimen, l = 300 mm Tensile stress, s = 500 MPa Modulus of Elasticity, E…

Q: A tensile stress is to be applied along the axis of a cylindrical steel rod that has a diameter of…

A: Given data : Poisson's ratio (μ)=0.3Diameter (d)=7.5 mmModulus of elasticity (E)=207 GPaChange in…

Q: Material Yield Tensile Strain at Fracture Elastic Strength StrengthFractureStrengthModulus (MPa)…

A: a) For material to experience the greatest percentage reduction in the area it should have a higher…

Q: During a tensile test on a specimen of steel the following data was recorded, diameter of specimen…

A: Given Information:

Q: A bar of length 2.0m is made of a structural steel having the stress-strain diagram shown in the…

Q: In a tensile test experiment of carbon steel. a standard specimen (D= 0.505 in. Gauge length=2.0 in…

A: Given DataDiameter of the specimen=0.505 inGauge length=2 inTotal length=8 inYield strength=80000…

Q: The elastic portion of the tension stress-strain diagram for an aluminum alloy is shown in the…

Q: Figure P1.16 shows the stress–strain relations of metals A and B during tension tests until…

A: (a) The proportion limit is the point on the the graph upto which the stress strain curve is…

Q: Determine the Poisson's ratio v.

Q: A cylindrical specimen of aluminum having a diameter of 12.8 mm and a gauge length of 50.800 mm is…

A: Given : D = 12.8mm F = 7300N Find : Stress ???

Q: 2. A steel bar, whose cross section is 0.55 inch by 4.05 inches, was tested in tension. An axial…

A: Cross-section of steel bar = 0.55x4.05 in2 Thickness (t) = 0.55 inBreadth (b) = 4.05 inLoad P = 30.5…

Q: A rod with a length of 1 m and a radius of 20 mm is made of high-strength steel.The rod is subjected…

A: Given data:

Q: A steel bar 100 mm long is subjected to a tensile stress o. If change in length of bar is 0.05 mm…

A: Given data- Length L=100 mm,change in length ∆L=0.05 mm,E=200 GPa, To Find- The value of stress…

Q: The information in the photo attached shows elastic properties of a human tibula bone. If you were…

A: To calculate the shear strain for given shear stress and shear modulus of elasticity. Given, Shear…

Q: Q1/ Consider the brass alloy for which the stress-strain behavior is shown in the figure below. A…

A: (a) Calculate the elongation as; Stress=EBrass×StrainForceArea=EBrass×∆LL2250…

Question

EXAMPLE 2.4. In an experiment, a steel specimen of 13 mm diameter was found to elongate
0.2 mm in a 200 mm gauge length when it was subjected to a tensile force of 26.8 kN. If the
specimen was tested within the elastic range, what is the value of Young's modulus for the steel
specimen ?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
4. A 2.0 m steel is being subjected into a tensile test. At force 30 kN, the length of the steel is now 2.2 m, but after the force has been released, the steel returned to 2.1 m. The state of the steel is at?
A 19-mm reinforcing steel bar and a gauge length of 75 mm was subjected to ten- sion, with the results shown in Table P3.27. Using a computer spreadsheet pro- gram, plot the stress-strain relationship. From the graph, determine the Young's modulus of the steel and the deformation corresponding to a 150-kN load. TABLE P3.27 Load, kN Deformation, mm 54 0.084 163 0.168 284 0.336 330 1.428 366 3.360
A specimen of steel has a rectangular cross section 20 mm wide and 40 mm thick, an elastic modulus of 207 GPa, and a Poisson's ratio of 0.30. If this specimen is pulled in tension with a force of 60,000 N, what is the change in width if deformation is totally elastic? O Increase in width of 3.62 x 10-6 m O Decrease in width of 7.24 x 10-6 m Increase in width of 7.24 x 106 m O Decrease in width of 2.18 x 10-6 m
If the yield stress in part c is considered failure stress, what is the maximumworking stress to be applied to this material if a factor of safety of 1.5 is used?
A mild steel specimen originally 300 mm long is pulled in tension with a stress of 500 MPa. If the deformation is entirely elastic, calculate the resultant elongation? The modulus of elasticity of steel is 200 GPa.
A tensile test was done on a steel specimen with the gauge length of 525 and a stress of 175 MPa. If the deformation is entirely elastic, what will be the resultant elongation? The modulus of elasticity of steel is 207 GPa.
Testing a round steel alloy bar with a diameter of 15 mm and a gauge length of 250 mm produced the stress–strain relationship shown in Figure Determinea. the elastic modulusb. the proportional limitc. the yield strength at a strain offset of 0.002d. the tensile strengthe. the magnitude of the load required to produce an increase in length of 0.38 mmf. the final deformation, if the specimen is unloaded after being strained by the amount specified in (e)g. In designing a typical structure made of this material, would you expect the stress applied in (e) reasonable? Why?
Can you solve this questions?
The shown figure represents the stress-strain relations of metals A and B during tension tests until fracture.Determine the following for the two metals (show all calculations and units):a. Proportional limitb. Yield stress at an offset strain of 0.002 in./in.c. Ultimate strengthd. Modulus of resiliencee. Toughnessf. Which metal is more ductile? Why?