Example 2. energy per hole during each revolution. Each piercing takes 40 per cent of the time needed to make one revolution. The punch receives power through a gear reduction unit which in turn is fed by a motor driven belt pulley 800 mm diameter and turning at 210 r.p.m. Find the power of the electric motor if overall efficiency of the transmission unit is 80 per cent. Design a cast iron flywheel to be used with the punching machine for a coefficient of steadiness of 5, if the space considerations limit A punching press pierces 35 hotes per minute in a plate using 10 kN-m of the maximum diameter to 1.3 m. Allowable shear stress in the shaft material = 50 MPa Allowable tensile stress for cast iron = 4 MPa

Example 2. energy per hole during each revolution. Each piercing takes 40 per cent of the time needed to make one revolution. The punch receives power through a gear reduction unit which in turn is fed by a motor driven belt pulley 800 mm diameter and turning at 210 r.p.m. Find the power of the electric motor if overall efficiency of the transmission unit is 80 per cent. Design a cast iron flywheel to be used with the punching machine for a coefficient of steadiness of 5, if the space considerations limit A punching press pierces 35 hotes per minute in a plate using 10 kN-m of the maximum diameter to 1.3 m. Allowable shear stress in the shaft material = 50 MPa Allowable tensile stress for cast iron = 4 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The gearing of a machine tool is shown in the Figure below. The motor shaft is connected to gear 1…

A: Speed of gear 1, N1=1200 rpmNumber of teeth on gear 1, T1=40Number of teeth on gear 2, T2=50Number…

Q: to make one revolution. The rough a gear reduction unit motor driven belt pulley 77

A: Given-Information:- Number of Holes, 40 per min Energy per hole, 10 kN-m = 10,000 N-m Diameter, d =…

Q: Two parallel shafts are to be connected by spur gearing. The approximate distance between the shafts…

Q: A gearbox is needed to provide an exact increase in speed, while minimizing the overall gearbox…

A: Given:Achieve an exact output speed of 13250 rpm while minimizing gearbox size and transmitting 18…

Q: pinion shaft of a machine transmits a torque of 66 Nm to the shaft of gear at a speed of 564 rpm,…

Q: A drive system for a large commercial band saw is to be designed to transmit 12 hp. The saw will be…

A: 1 HP = 745.7 = 746 WATT 12 HP = 12 * 746 = 8952 W = 8.952 KW pinion rotates NP = 3450 rpm gear…

Q: 10. What is the minimum diameter in mm of a steel shaft which will be used to operate a 14 kN-m…

Q: submit any example for shaft and gear and design them finding the bellow 1- the contact stress for…

A: given; (a)the contact stress for the shaft and gear (b)the bending stress for the shaft and gear

Q: The request is to design the input shaft diameter for a double step-up gearbox with a 25⁰ pressure…

A: Gear box Gear box is used to increase the speed of engine. Gears are engaged together to increase…

Q: The figure below represents a pair of spur gear fitted on a lathe machine. A power of 6 kW at 657…

A: P=6 KW N=657 rpmTP=29TG=72 m=8 mm φ=20° since P=2πNPT60T=P×602πNPT=6×103×602π×657T=87.208 N-m

Q: A 48 in diameter diamond saw blade is mounted on a pulley driven steel shaft, requiring a blade…

A: Given 48 in diameter diamond saw Angular velocity = 150 ft/sec Power = 125 hp Rotation = 1200 rpm…

Q: (machine dynamic) The variation diagram of the cutting force of the cutting work done with the…

Q: Two mating spur gears have 40 and 120 teeth respectively. The pinion rotates at 1200 rpm and…

A: Two mating spur gears have Z1 = 40 and Z2 = 120 teeth respectively. The pinion rotates at N1 = 1200…

Q: I have a 52100 steel hollow shaft, that will be threaded into a 1 inch thick plate of aluminum 7075.…

A: Step 1:For a steel shaft threaded into an aluminum plate, it's crucial to consider the potential for…

Q: A gearbox is needed to provide an exact increase in speed, while minimizing the overall gearbox…

A: Given:The power required to transmit gearbox is .The output speed is .The input speed is .Formula…

Q: a uniformly loaded conveyor with a required shaft speed of approximately 531 r/min. Use a pinion…

Q: Design a pair of plastic gears to drive a small band saw, using the following data: The input is…

Q: For a bevel gear, given that: Face width ( F) = 4 in One member is straddle mounted Then the…

Q: In the double-reduction gear train shown (dimensions are in inches), shaft a is driven by a motor…

A: Step 1: Step 2: Step 3:

Q: In a broaching machine shown, shaft A carries a pulley 60.96 cm in diameter which is driven by a…

Q: A pair of spur gear fitted on a motor shaft of lathe machine transmits the power of 7 kW at 600 rpm…

A: Given Data P=7 kW Np=600 rpm Zp=22 Zg=72 m=8 mm

Q: Problem # 4: The turbine motor moving at 378 rev/ min can produce 2.5 hp. The shaft diameter is 1.25…

A: Let T=Torque developed in the shaft d= diameter of shaft =1.25inches=0.03175m P = Power of…

Q: A power of 120 kW is transmitted into a single reduction gear system through a pinion with 250 mm…

Q: each part A - A weight of 1500 N must be lifted. What is the total required torque necessary to…

Q: 12. A cylinder with a bore diameter of 100 mm and a rod diameter of a 40 mm is to be used in a…

Q: machine transmits the power of 5 kW at 672 rpm which is input at pinion gear and its shaft rotates…

Q: An electric motor purchased by your employer surprisingly arrived without a keyway in the shaft. The…

A: Given : d = 17 mm To find : Design a square key

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

Example 2.
energy per hole during each revolution. Each piercing takes 40 per cent of the time needed to make
one revolution. The punch receives power through a gear reduction unit which in turn is fed by a
motor driven belt pulley 800 mm diameter and turning at 210 r.p.m. Find the power of the electric
motor if overall efficiency of the transmission unit is 80 per cent. Design a cast iron flywheel to be
used with the punching machine for a coefficient of steadiness of 5, if the space considerations limit
A punching press pierces 35 hotes per minute in a plate using 10 kN-m of
the maximum diameter to 1.3 m.
Allowable shear stress in the shaft material = 50 MPa
Allowable tensile stress for cast iron = 4 MPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Trending now

This is a popular solution!

Step by step

Solved in 9 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

I have a 52100 steel hollow shaft, that will be threaded into a 1 inch thick plate of aluminum 7075. The shaft is 960 mm in length, 40 mm OD and 20 mm ID. The threaded end of the shaft is M30X3.5. What would be the recommended torque for the shaft, with the dissimilar metals. I’m expecting a range between 100-280 ft-lbs but can justify it.
1-Show how the roughness is indicated for a Surface to be coated, obtained by any production method with N6 showing max. and min roughness. 3- gearing is suitable for two shafts at 90°. : Draw five turns of a compression spring of wire diameter 6mm, pitch 12 num and outside diameter of 38mm.
3. Design Challenge: The wind turbine is designed to generate 2.5 MW of power with the blades rotating at 20 RPM. The large gear has 360 teeth and the small gear has 12 teeth. Design the high speed shaft to minimize weight. That is, choose a material (from your textbook) and cross-section dimensions such that the shaft won't yield, with a safety factor of 2.5, while keeping the shaft's weight to a minimum. Calculate the weight per meter of the shaft you designed. 2 Gear reducer High speed shaft Low speed shaft Generator
Hand written plzzzzzzz....both parts
Correct and complete solution
A pinion shaft of a machine transmits a torque of 42 Nm to the shaft of gear at a speed of 578 rpm, which is input at pinion gear and its shaft rotates in the clockwise direction. The number of teeth on the pinion and the gear are 38 and 78 respectively, while the module is 6 mm. Assume a pressure angle of 200. Calculate: i) Power transmitted by the shaft of the pinion in W. ( ii) Torque on the shaft of the gear in Nm. iii) Speed ratio iv) Tangential load on the pinion in N
HW12 The gearing of a machine tool is shown in the Figure below. The motor shaft is connected to gear A and rotates at 1500 r.p.m. The gear wheels B, C, D and E are fixed to parallel shafts rotating together. The final gear F is fixed on the output shaft. Fined: 1-the speed of gear F 2- rotating speed of gears (B, C, D and E) The number of teeth on each gear are as given below: Gear A B C D E F No. of teeth 25 35 90 30 80 60 + A B E+ D F LL
24 A pinion shaft of a machine transmits a torque of 60 Nm to the shaft of gear at a speed of 516 rpm, which is input at pinion gear and its shaft rotates in the clockwise direction. The number of teeth on the pinion and the gear are 36 and 84 respectively, while the module is 6 mm. Assume a pressure angle of 20°. Calculate: i) Power transmitted by the shaft of the pinion in W. ii) Torque on the shaft of the gear in Nm. iii) Speed ratio iv) Tangential load on the pinion in N
A motor is used to drive a gear assembly at 200 rpm. The main gear is in the center of a 1 m long (0.5 m to the left and right of the gear) 50 mm diameter solid circular shaft, and power is taken from the two shaft ends. 25 kW is taken on the left end and an unknown amount of power is taken at the right end. the torque to the left side of the gear is? maximum shear stress to left of gear? If the maximum shear stress on the shaft to the right of the gear is 125 MPa, approximately how much power is being drawn off from the right side of the shaft? The shaft can be made from 6061-T6 aluminum. It has adequate strength to withstand the loading conditions in the scenario, including the loading on the right side of the shaft. true or false?
A pinion shaft of a machine transmits a torque of 68 Nm to the shaft of gear at a speed of 574 rpm, which is input at pinion gear and its shaft rotates in the clockwise direction. The number of teeth on the pinion and the gear are 38 and 78 respectively, while the module is 6 mm. Assume a pressure angle of 200. Calculate: i) Power transmitted by the shaft of the pinion in W. ii) Torque on the shaft of the gear in Nm. iii) Speed ratio iv) Tangential load on the pinion in N
9.10 An aircraft engine drives a propeller through a reduction drive shown in Fig. 9.27. The gears 1, 2, 3 and 4 have 48, 27, 45 and 120 teeth respectively. Find the propeller speed in magnitude and direction if the engine makes 2500 r.p.m. Arm Propeller Engine 1
I want to buy a two METAL SPUR GEAR for my 2 pieces of G.I pipe with an 4 inches diameter x 3 mm thick with (2 Stainless Steel Round Plate Thick=7mm in 2 holes) with (STAINLESS Steel Shafting Solid Round Bar 1 inches diameter)for my Roller Press refinement compress Project. I want the hole of spur gear=1 inch diameter. Determine the specifications of spur gears and what I need to buy spur gear size in market show their model of metal spur gear.