A pair of spur gear fitted on a motor shaft of lathe machine transmits the power of 7 kW at 600 rpm which is input at pinion gear and its shaft rotates in the counter-clockwise direction. The number of teeth on the pinion and the gear are 22 and 72 respectively, while the module is 8 mm. Assume a pressure angle of 20°. Calculate: i) Torque on the shaft of the pinion in Nm. i) Torque on the shaft of the gear in Nm. iii) Gear ratio iv) Center distance between shafts in mm

A pair of spur gear fitted on a motor shaft of lathe machine transmits the power of 7 kW at 600 rpm which is input at pinion gear and its shaft rotates in the counter-clockwise direction. The number of teeth on the pinion and the gear are 22 and 72 respectively, while the module is 8 mm. Assume a pressure angle of 20°. Calculate: i) Torque on the shaft of the pinion in Nm. i) Torque on the shaft of the gear in Nm. iii) Gear ratio iv) Center distance between shafts in mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

b) Figure Q1b shows a compound gear train with Gear A as the pinion (or driver) with an input Power (Pin) of 600 W at Gear A. If Gear A rotates at 139.70 rpm and engages with Gear B, calculate the angular velocity (w) in rad/s for Gears B, C & D; and the input torque (Tin) in at Gear A and output torque (Tout) at Gear D. The number of teeth (N) for gears A, B, C & D are 62 teeth, 34 teeth, 42 teeth and 22 teeth, respectively. Assume 100% efficiency and no frictional losses; and give your answers to two decimal places. GEAR A GEAR C GEAR B GEAR D
In a single-stage gear wheel system with an evolvent profile, the rotating (driveThe number of teeth of the gear is Z1=10, the number of teeth of the rotated gear is Z2=20 and the modulus is m=5 mm; The rotating gear rotates clockwise. b)Show the useful working length and the limit working length on the figure
A worm drive transmits 15 kW at 2000 rpm to a worm gear having 90 teeth with 6mm module. The worm is triple threaded and has 65 mm pitch diameter. The tooth form is to be 20 degrees full depth involute. Determine: a) the lead and lead angle of the worm A. b) The center distance between worm and gear. c) The tangential force acting on worm. d) The axial force acting on worm e) The radial force acting on worm
A pinion shaft of a machine transmits a torque of 42 Nm to the shaft of gear at a speed of 578 rpm, which is input at pinion gear and its shaft rotates in the clockwise direction. The number of teeth on the pinion and the gear are 38 and 78 respectively, while the module is 6 mm. Assume a pressure angle of 200. Calculate: i) Power transmitted by the shaft of the pinion in W. ( ii) Torque on the shaft of the gear in Nm. iii) Speed ratio iv) Tangential load on the pinion in N
24 A pinion shaft of a machine transmits a torque of 60 Nm to the shaft of gear at a speed of 516 rpm, which is input at pinion gear and its shaft rotates in the clockwise direction. The number of teeth on the pinion and the gear are 36 and 84 respectively, while the module is 6 mm. Assume a pressure angle of 20°. Calculate: i) Power transmitted by the shaft of the pinion in W. ii) Torque on the shaft of the gear in Nm. iii) Speed ratio iv) Tangential load on the pinion in N
Two spur gears are to have a ratio of 9:3 and a 7mm module. If the center distance is to be approximatively 200mm, calculate the following:o Circular pitch value;o Number of teeth on the wheel (gear);o Number of teeth of the pinion;o Pitch circle diameter of the gear;o Pitch circle diameter of the pinion;
Ex] A double-threaded right-handed worm gear transmits 15 Hp at 1150 rpm. The pitch of the worm is 0.75 inch and the pitch diam of 3 inches. The pressure angle is 14.5° and the coefficient of friction is 0.12. a) Find the tangential force on the gear. b) Find tangential force on worm. c) Find the separating force Solution: (To be discussed by the Instructor during the lecture period)
Please assist
Kindly help?
A pinion shaft of a machine transmits a torque of 68 Nm to the shaft of gear at a speed of 574 rpm, which is input at pinion gear and its shaft rotates in the clockwise direction. The number of teeth on the pinion and the gear are 38 and 78 respectively, while the module is 6 mm. Assume a pressure angle of 200. Calculate: i) Power transmitted by the shaft of the pinion in W. ii) Torque on the shaft of the gear in Nm. iii) Speed ratio iv) Tangential load on the pinion in N
An electric motor develops 8 HP at 2652 rpm. An 19 tooth gear is fitted to its output shaft to drive a gear on an output shaft. How many teeth would be needed on this output gear if an output torque of 92 Nm is required? Answer: Next page page Finis Time 9Type here to search