A worm drive transmits 15 kW at 2000 rpm to a worm gear having 90 teeth with 6mm module. The worm is triple threaded and has 65 mm pitch diameter. The tooth form is to be 20 degrees full depth involute. Determine: a) the lead and lead angle of the worm A. b) The center distance between worm and gear. c) The tangential force acting on worm. d) The axial force acting on worm e) The radial force acting on worm

A worm drive transmits 15 kW at 2000 rpm to a worm gear having 90 teeth with 6mm module. The worm is triple threaded and has 65 mm pitch diameter. The tooth form is to be 20 degrees full depth involute. Determine: a) the lead and lead angle of the worm A. b) The center distance between worm and gear. c) The tangential force acting on worm. d) The axial force acting on worm e) The radial force acting on worm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i need the answer quickly
i need the answer quickly
In a single-stage gear wheel system with an evolvent profile, the rotating (driveThe number of teeth of the gear is Z1=10, the number of teeth of the rotated gear is Z2=20 and the modulus is m=5 mm; The rotating gear rotates clockwise. b)Show the useful working length and the limit working length on the figure
A gear box has an input speed of 1800 rev/min clockwise and an output speed of 400 rev/min The input power is 25kW and the efficiency is 90%. Compute the input torque the output power 3. the output torque
24 A pinion shaft of a machine transmits a torque of 60 Nm to the shaft of gear at a speed of 516 rpm, which is input at pinion gear and its shaft rotates in the clockwise direction. The number of teeth on the pinion and the gear are 36 and 84 respectively, while the module is 6 mm. Assume a pressure angle of 20°. Calculate: i) Power transmitted by the shaft of the pinion in W. ii) Torque on the shaft of the gear in Nm. iii) Speed ratio iv) Tangential load on the pinion in N
Two spur gears are to have a ratio of 9:3 and a 7mm module. If the center distance is to be approximatively 200mm, calculate the following:o Circular pitch value;o Number of teeth on the wheel (gear);o Number of teeth of the pinion;o Pitch circle diameter of the gear;o Pitch circle diameter of the pinion;
pls expalin to me step by step and write clearly. i will rate your answer immediately thanks
Ex] A double-threaded right-handed worm gear transmits 15 Hp at 1150 rpm. The pitch of the worm is 0.75 inch and the pitch diam of 3 inches. The pressure angle is 14.5° and the coefficient of friction is 0.12. a) Find the tangential force on the gear. b) Find tangential force on worm. c) Find the separating force Solution: (To be discussed by the Instructor during the lecture period)
Please assist
Hello good Afternoon Sir, Permission, i have a question in my homework. The following bellow is question. Please advice. Thank you Regards,Irfan In planning the combined gears of the Ferguson planetary paradox as shown in the figure below.Sun gear hand input with angular speed (w2) = 0 rpm and hand input with angular speed (w.arm) = 400 rpm counterclockwise (ccw)Where is the number of teeth:Sun gear N2 = 100 (external gear)Sun gear N3 = 99 (external gear)Sun gear N4 = 101 (external gear)Planet gear N5 = 20 (external gear)Calculate the angular velocity, for each gear using the tabulation method. The data is in the image below
A pinion shaft of a machine transmits a torque of 68 Nm to the shaft of gear at a speed of 574 rpm, which is input at pinion gear and its shaft rotates in the clockwise direction. The number of teeth on the pinion and the gear are 38 and 78 respectively, while the module is 6 mm. Assume a pressure angle of 200. Calculate: i) Power transmitted by the shaft of the pinion in W. ii) Torque on the shaft of the gear in Nm. iii) Speed ratio iv) Tangential load on the pinion in N
The spur gear arrangement shown in the figure has a pinion (diver Gear A) that rotates at 625 rpm, an idler Gear B and a driven gear (Gear C). The gears have a module of 5 mm and a pressure angle of 20 degrees. Given the number of teeth as shown in the figure, determine: i) ii) iii) The pitch diameters of each of the gears. The torque that each shaft is required to transmit. The forces on each of the gears 40 teeth 490⁰ B 70 teeth 50 teeth