Example 10.3 Uniform Flow, DetermineFlow Rate• Water flows in the canal of trapezoidal cross section shown in Fig.E10.3a. The bottom drops 1.43 mper 1000 m of length. Determine theflowrate if the canal is lined with new smooth concrete. Determinethe Froude number for this flow.Q= AVRh = Area / wetted perimetery = 1.52 m40°40°40°R;³s/2V =Fr = V //gyManning equationn= 0.012

Given:Depth of flow y = 1.52 mWidth b = 4 mSlope m = 40°

Answered: Example 10.3 Uniform Flow, Determine…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Cipolletti weir, popular in irrigation systems, is trapezoidal,with sides sloped at 1:4 horizontal to vertical, as in Fig. The following are flow-rate values, from the U.S.Dept. of Agriculture, for a few different system parameters. Use this data to correlate a Cipolletti weir formula with areasonably constant weir coefficient.
Q1: A canal of trapezoidal section has bed width of 8 m and bed slope of 1 in 4000. If the depth of flow is 2.4 m and side slopes of the channel are 1 horizontal to 3 vertical, determine the average velocity and the discharge carried by the channel. Also compute the average shear stress at the channel boundary. Take C = 55.
QUESTION 2 At a certain location in Durban, under normal conditions the water flows uniformly in a finished-concrete rectangular channel. During the recent floods' conditions, the overflow regions consisting of light brush was observed to increase the flow rate by 45%. Estimate the depth D if the bottom slope of the channel is 0.1°. D 1.5 m -5 m -5 m 2 m Figure 1
Q1: what is the head above the crest of the notch (weir) shown in figure below, in order to make the theoretical discharge through it equals(0.0403 m/sec). H O.2m
Water flows in a rectangular channel that is 0.5 m wide as shown. The upstream depth is 70 mm. The water surface rises 40 mm as it passes over a portion where the channel bottom rises 10 mm. If viscous effects are negligible. What is the flow rate? (2) 100 mm (1) 70 mm 10 mm
1. Determine the depth (yo), bearing area (A), and wet circumference (P) of a trapezoidal shaped channel with the following known data mi = 2,5 m2 = 3,5 b = 5,5 m 1. mi Q = 24,5 m³/s m2 n= 0,014 So = 0,0003 %3D
A hydraulic jump is shown in figure below. The depth of flow z₂ after the hydraulic jump is 5 m larger than z₁. The total flow rate in the channel is 450 m³/s and the channel width is 50 m. The length / over which the jump occurs is 0.4 m. ax= If the depth, z₁, is 6 m then what is the average acceleration (ing's) of the liquid as is flows across the jump. 0.21 Hydraulic jump g's V₂
Water in a two-dimensional channel flows smoothly over a submerged obstacle of height H as shown in Figure P10.12. The water depth at the peak of the obstacle is Y2, where Y2 = Y1/3. (a) Find the value of the Froude number of the incoming flow, F1, given that the Froude number is unity at the point where the depth is Y2. (b) Find the nondimensional height of the obstacle, H/Y1.
1. An actual discharge from a reservoir takes place over a rectangular weir where the flow characteristic is Q= 1.77 BH 3/2 m³/s (a) Find the length of weir (b) The ratio of actual discharge to theoretical discharge * Required to discharge 9 m³/s, if head must not exceed 0.6m

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS