3. Water flow in a rectangular channel, with a maximum velocity of 2 m/s at the surface. Determine the (Dimensions of the channel are 2-m wide, and 3-m deep) a) The average velocity of the fluid. b) The volume flow rate. c) The mass flow rate.

Q: the sketch top, front, and right side isometric below. For the objects shown in sure that your views…

A: According to the details provided in the question we need to draw three projection view of the given…

Q: ADD MISSING LINES (VISIBLE OR HIDDEN) TO EACH OF THE PROBLEMS BELOW. XX * 30

A: Given: Photographic views: Top view, Front View and Right View.To draw: Missing lines for each…

Q: Given drawing of a Mechanical component, study the drawing carefully and then using Inventor, AUOB…

A: 1. Create the 3D Model of the part.

Q: The product from an open - circuit primary rod mill receiving 160 tons/hour of new ore feed joins…

A: Given:Rod mill product stream:  solids by weight.Ball mill product stream:  solids by…

Q: SKETCH COMPLETE FRONT, RIGHT AND TOP VIEWS. SHOW ALL HIDDEN LINES. LABEL SURFACES.

A: Orthographic views of the given isometric view are drawn on the grid paper. 1 Grid = 1 Unit

Q: What type of scale is 10:1? O Full Scale O Enlargement Scale O Reduction Scale

A:

Q: Name the feature shown below. 10 00

A: the feature displayed in the picture is extrude

Q: What is the key information that needs to be incuded in a section view on an assembly drawing.…

A: The Answer is below

Q: General Questions Not Directly Related to the Print 1.  A ________ print is a supplemental print…

A:

Q: Design the solid model shown.  There should only be 4 sketches max and an applied feature. This…

A: according to the given details in the question.

Q: OA F >F>F OE- F = F, F, >F, >F, F > F, >F, D) OF> F >F,

A: Forces on the surfaces, F1,F2,F3 Area of each surfaces, 2S,S,3S

Q: Freehand sketch a set of front/top/right views

A: According to the given data A 3D object is given We need to draw Three projection view of the object…

Q: General Questions Not Directly Print Related) 1.  ____________use conventional symbols with single…

A: Fill in the blanks

Q: 8 - A robot is used for loading and unloading of parts to automated flexible machines. Loading time…

A: Write the given data. tmachine=15 min        C1=30 TL/hour        C2=40 TL/hour Here, tmachine is…

Q: Select the correct statement below regarding the two solid model parts shown. (A) (B) It is easiest…

A: In the figure two solid model parts are given. The extrusion is in which the two dimensional shape…

Q: Subparts 1, 2, and 3.

A:

Q: The circular pattern feature can be used in creating the following part. True False

A: Circular patterns are used to draw the circular solidworks diagram as shown in the given figure.For…

Q: Using autocad draw necessary views. Kindly all the views I'll rate your solution

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: What type of scale is 1:1? Full Scale O Enlargment Scale Reduction Scale

A: Scale factor is the ratio of the length of the drawing to the actual length of the object. The scale…

Q: Name the feature shown below.

A: The given figure is of

Q: -30- R-64 20 -10 (5.0) -50 -40 -30 -20 -10 10 10-

A: given:

Q: I need these 3 parts answered TRUE or FALSE.

A: During the life of any product, parts used for many years are replaced to improve the efficiency or…

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.