Example 10: The box wrench in Figure (a) is used to tighten the bolt at A. If the wrench does not turn when the load is applied to the handle, determine the torque 300 mm- 400 mm or moment applied to the bolt and the force 60 of the wrench on the bolt. 52'N 30 N (a)

Example 10: The box wrench in Figure (a) is used to tighten the bolt at A. If the wrench does not turn when the load is applied to the handle, determine the torque 300 mm- 400 mm or moment applied to the bolt and the force 60 of the wrench on the bolt. 52'N 30 N (a)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Ⓒ Betermine the reactions & draw the flear and bending moment diegrams for frame below. using the force method. soku/m ㅈㅈ I E = Constant 4m 21 5 B2 75kW * 42 1m E
Q1-A/ Determine the moment of the force system shown in Figure (1A) with respect to point A. 8. 8 100 N Figure (1A) 130 N
A 200-Ib block is suspended from an inextensible cable which is wrapped around a drum of 1.3-ft radius rigidly attached to a flywheel. The drum and flywheel have a combined centroidal moment of Inertia IG=10 Ib-ft-s^2 At the instant shown, the velocity of the block is 5 ft/s directed downward. Knowing that the bearing at A is poorly lubricated and that the bearing friction is equivalent to a couple M of magnitude 60 Ib-ft, determine the work or U1->2 (in ft-Ib) after it has moved 4.2 ft downward
The shaft is connected to a generator at A and the torque applied at each of the four gears is as follows: Tu = 40 N.m. T. = 25 N.m. T, 34.5 N.m. T, 23 Nm. The shaft is made of Aluminum 2014-T6 and H has a polar moment of inertia J= 2 *10 m. Find the angle of twist of gear E with respect to gear D knowing that the distance between the two gears is 840 mm. O0.0537 rad O0.0358 rad 10.0132 rad O 0.933 rad 40.0179 rad
The magnitude of the force Q is 896 N. Determine the magnitude of the moment (Nm) of Q about point C. Round off only on the final answer expressed in 3 decimal places.
Q1. For the mechanism shown in figure, at this particular instant the vertical shaft is rotating along z-axis with a constant angular velocity (@ = 2 rad/sec). Note: When force F is applied on sleeve "J", it can slide up and down on vertical shaft (while sleeve "I " is fixed) and 0 can vary between 0° to 90° Select five right answers. 0.3 m 0.3 m a. All links (GH, EF, AB and CD) will have same angular velocity b. All links (GH, EF, AB and CD) will have different angular velocity E 0.3 m 0.3 m G c. Tangential Acceleration (a) of link AB will not be zero d. Tangential Acceleration (a) of link CD will be zero A e. Angular Acceleration (a) of link AB will not be zero 0.1 m 0.1 m f. Angular Acceleration (a) of link CD will be zero g. All points on link CD will have same linear velocity, when 0 = 0° h. All points on link AB will have same linear velocity, when 0 = 90° F i. Point B on link AB will have maximum linear velocity, when 0 = 90° j. Point D on link CD will have maximum linear…
STATICS OF RIGID BODIES (CHOOSE THE CORRECT ANSWER IN THE CHOICES. WRITE THE SOLUTIONS LEGIBLY. NO LONG EXPLANATION NEEDED.)
Read the question carefully and give me right solution according to the question. Note: Don't copy from other experts answer
Draw the Shear Force (V) and Bending Moment (M) diagrams of statically indeterminate beam shown in figure using “Force Method". The (roller) support at “B" settles 35 mm. The moment of inertia is given by (I) for regions “AB", “BC" and “CD"; however it is equal to (21) for the region “DE". (“B" is the roller and “E" is the fixed type of support). [The flexural rigidity: El=40000 KNM²] 60 kN 10 kN/m ►X В (I) (1) (I) (21) 1.5m
The coefficient of static friction between the block and the sloping plane is 0.41, and the coefficient of friction between the rope and the fixed cylindrical shaft is 0.13. I need both the minimum and maximum force answered in the image below.
5.
Given: Fi Tft Ift 2ft pt.0 F1 = 48 kips %3! F2 = 73 kips Required: Calculate the resultant moment of the forces about point O. Assume a positive moment is counter-clockwise (CCW+). Enter a positive value along with (CW) or (CCW) next to the value to indicate the actual direction of the resultant moment.