Ex-6. A steel tape with a cross-sectional area of 0.039 cm? and weighing 0.909 kg has a length of 30.009 m. when supported throughout 20°C and subject to a tension of 5.5 kg. This tape is used to measure a distance along a uniform 4% grade and is supported throughout during the measurement. The tension applied is 12 kg. The temperature of the tape is 2°C. The measured slope distance is recorded 381.615 m. What is the corrected horizontal distance? in Awa

Ex-6. A steel tape with a cross-sectional area of 0.039 cm? and weighing 0.909 kg has a length of 30.009 m. when supported throughout 20°C and subject to a tension of 5.5 kg. This tape is used to measure a distance along a uniform 4% grade and is supported throughout during the measurement. The tension applied is 12 kg. The temperature of the tape is 2°C. The measured slope distance is recorded 381.615 m. What is the corrected horizontal distance? in Awa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q:8/ A steel wire (10m) long, hanging vertically supports a tensile load of (2000N). Neglecting the weight of the wire, determine the required diameter if the stress is not to exceed (140MPA) and the total elongation is not to exceed (5mm)..Assume (E=200GPA).
Q2: Neglecting the effect of fillets and of stress concentrations, determine the smallest permissible diameters of the solid rods BC and CD. Use Tall = 60 MPa. 500 N 180 mm 160 mm 1250 N B 200 mm D
Q2/ The rigid, horizontal slab is attached to two identical copper rods. There is a gap A=0.18 mm between the middle bar, which is made of aluminum, and the slab. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased by 85°C. Use the following data: Each copper rod Aluminum rod A (mm²) 500 400 a (°C) 16.8 x 10-6 23.1 x 10-6 E (GPa) 120 70 Copper TA Aluminum Copper L=3m A= 1500 mm E=120 GPa a = 16.8 x 10-C Copper -750 mm-
Please answer asap with clear and complete solutions .thank you
17-18. A horizontal steel rod, 3.2 m long and 1200 mm² in cross-sectional area is secured between two walls. If the rod is stress free 30°C, compute the stress when the temperature has dropped to -15°C. Use a = 11.7 x 10° mm/mm°C and E = 200 GPa. What is the stress assuming the walls are rigid? Ina D. 46.80 MPa Cs Scenozoith Cars C. 35.10 MPa What is the stress assuming the walls yield(moves) by 0.45mm? A. 6.98 MPa B. 18.68 MPa C. 36.42 MPa D. 53.78 MPa
5) Given the stresses shown at an arbitrary point, calculate the principal stresses and the max shear stress (15 Points) бу = 100 MPa H L C # DELL O Ⓡ 7 88 Txy = 55.9 MPa √x=200MPa
I need the answer as soon as possible
The standard length of a tape is 100m having a weight of 1.2kg with the standardtemperature of 20 C and standard pull of 5.5kg. The young modulus of elasticity of thetape is 200GPa, cross sectional area is 2.8mm? and the coefficient of linear expansionis 0.0000116/°C. Determine the normal tension of the tape.
(a) (b) (c) Given, (i) area of Z100 x 100 x 8 = 15.39 cm2, %3D (ii) thickness of gusset plate = 10 mm (iii) nominal diameter of rivets = 16 mm, %3D (iv) permissible tensile stress = 150 MPa, and (v) as per IS : 800 (1984) for single angle, the net effective area = A, + KA, %3D ЗА, K = (3A, + A2) where, A, = effective cross-sectional area of the connected leg, the gross cross-sectional area of the A2 %3D unconnected leg
i need the answer quickly
please draw a proper free body diagram and answer in complete solution
SHOW COMPLETE SOLUTION AND ILLUSTRATION