Answered: € 2 L 46 1) Consider two cylindrical… | bartleby

Related questions

Question

ela
R
L
2L
lenda
6 Pail
1) Consider two cylindrical copper resistors (wires). The shorter wire length L and radius R.
The longer wire has length 2L and radius.
a) Call the resistance of the shorter wire Rs and the resistance of the longer wire RL. What
is RL in terms of Rs
b) At a Constant voltage V what are the respective currents Is and IL in terms of Rs or
RL? Which has a greater current.

Expert Solution

Step by step

Solved in 5 steps with 9 images

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

If three resistors connected in series to a battery. Suppose R1 carries a current of 2.5A, R2 has a resistance of 12.52, and R3 dissipates 70W of power. What is the voltage across R3 and Resistance of R3 ? 1. Voltage (in V) across R3 and 2. Resistance (in 2) of R3 %3D
B2
If three resistors connected in series to a battery. Suppose R, carries a current of 14.5A, R2 has a resistance of 7.5N, and R3 dissipates 55W of power. What is the voltage across R3 and Resistance of R3 ? 1. Voltage (in V) across R3 = and 2. Resistance (in Q) of R3 ||
Ei
letter d only
I'm trying to understand this figure Assume the capacitor in the circuit is initially uncharged. Can you calculate the current through each resistor right after the circuit is connected? If so, can you explain and show how you did it? What if the circuit has been connected and left alone for a long time. Calculate the charge on the capacitor plate
a) Write an equation for the currents entering in/out of the top junction in Figure 1. Use I1 as the current coming from the left, I2 as the current going downward, and I3 as the current going to the right. b) You can draw three loops in order to solve this circuit. Write the corresponding voltage equations for these loops in terms of V1, V2, VA, and VB; where VA and VB are voltages across the resistors RA and RB respectively. c) Using Ohm's law combined with the equations you found above; express I1, I2, and I3 as equations in terms of the know quantities V1, V2, RA, and RB. d) Now you have all the information you need to express VA and VB as equations in terms of V1, V2, RA, and/or RB.
QI) Answer the following as True or False a- During the Specific Charge of Copper experiment, the quantity I t is constant. b- The potential difference betwveen the anode and cathode during the Electric Field Mapping experiment depends on the position of the sliding contact along the rheostat. c- The ratio I/N for an Ohmic conductor is constant and equal to the resistance of the conductor. d- The equivalent resistance of an Ohmic resistance and a non-Ohmic resistance connected in series is their sum.
X N 3) Consider a cube whose center is at the origin, and all edges of the cube are 4 cm. A battery (DC voltage) with voltage of Vo is connected to bottom and top faces (sides) of cube as shown in left figure. a) If the volume current density in cube is given as; J=100 V₁ (x² + y²)â. A/m² then find the (DC) resistance of the structure. Hint: You can get the result without considering below part (part b). O= b) By assuming that electric field intensity is zero outside the cube (although practically there is nonzero electric field outside the cube, assume that this electric field is very small), if the conductivity of the material of the cube is given as; x² 1+ Z 0.02 10-2 S m then find and express free charge densities (where they exist) in terms of battery voltage Vo. Take cube material's relative permittivity (dielectric constant) as &r = 1.
The current through the resistor of resistance Ra in the circuit below is: R. from left to right. V from right to left. B. V from left to right. R,+R,+R3 V from right to left. R,+R,+R,
Which of the following is an installation requirement for the grounding electrode conductor in a communications system? A. It must be run as straight as practicable. B. It must be, at minimum, 4 AWG. C. It must be solid or stranded aluminum. D. It must be isolated and covered.
letter b only