erature is 32 ASSUMPTIC

Q: A particle starts from rest at x = -2.7 m and moves along the x-axis with the velocity history…

A:

Q: steel structure

A: Steel structures are widely used in modern construction due to their strength, durability, and…

Q: Characteristics and features of the oven

A: Microwaves are generated inside the oven by an electron tube known as a magnetron. The microwaves…

Q: how did you find humidity ratio

A:

Q: An oil pump operating at steady state delivers oil at a rate of 11 lb/s through a 1-in-diameter exit…

A:

Q: 18. How far off from the center of the support is the center of the two holes in the bosses of the…

A: 18)    Distance=4.2-0.66                   =3.54 in

Q: In an air-standard Otto cycle engine, the following data were obtained: k = 1.4, cp = 1.0045₂ =…

A:

Q: A polytropic process of air from 150 psia, 300°F, and 1 ft³ occurs to p₂ = 20 psia in accordance…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: (a) Demonstrate five processes that make up the air-standard dual cycle.

A: GIVEN DATA- AIR-STANDARD DUAL CYCLE GIVEN WE HAVE TO DEMONSTRATE ALL FIVE PROCESS

Q: A pump is to be placed at the beginning of a 30 m long piping system consisting of 1-1/2 inch…

A: Release head differs with pull tank level. The response is yes. Assuming you bring down the pull…

Q: 5/90° 0.2/180°

A: Given as,…

Q: Air (C. = 1.005 kJ/kg-K, R = 0.287 kJ/kg⋅K) enters a compressor operating at steady state at 1.05…

A:

Q: A steam power plant operates on a cycle as shown in the figure. The fluid leaves the boiler at 400…

A:

Q: inside diameter = 7cm tap 100 cm Item#2 You and your friends ordered a

A: GivenQ=3.5ltrz2=2cmD1=7cmd2=1cmh=100cm

Q: A steam enters the condenser with an enthalpy of 2234 kJ/kg. If the condensed steam leaves t…

A: Given:h1=2234 KJ/Kgh2=321 KJ/KgQ=5000 KW

Q: Section 2: Numerical Response Q3 : If the flow into a wind turbine is 10 m/s, and the flow far…

A: Given:The upstream velocity of flow, The downstream velocity of flow,

Q: nd P7.11 40 MPa The grain of a wooden member forms an angle of 15° with the vertical. For the state…

A: The shear stress

Q: 3. both wires is identical at 1.5 meters and both wires are 5 mm in diameter. The steel wire is made…

A:

Q: SKETCH: (Name and label each parts of CLEVELAND OPEN-CUP FLASH POINT TESTER). SYD-3536 HASĦORAKSH

A: Flash point testing: The purpose of flash point testing is to ascertain the flammability of a…

Q: A high-pressure hot water system has a total volume of 3m³. Calculate the expansion volume that…

A: Given :The total volume of a high-pressure hot water system, The initial temperature of the system,…

Q: Determine the weld macrostructures at point X and Y as Figure 1(b).

A:

Q: what happened with the 10 in the first equation?

A:

Q: interpolations/extrapolations: NO Calculator Technique and Applications. 1. Five kilo of water…

A: As per the guidelines of BARTLEBY we are subjected to solve only one question at a time. Please…

Q: G R.75 00.63 THRU E 01.123 F0.250 T 2.00 1.00 1.38 1.123 mm diameter hole with depth of 0.250 mm…

A:

Q: How to do heat loss by thermal cooling?

A: Thermal cooling Thermal cooling is defined as the achieving the lower temperature by means of…

Q: using rogers and mayhew's table please answer the question

A: The solution is given below-Explanation:Step 1: Step 2: Step 3: Step 4:

Q: 1) An ideal gas' temperature changes from 300 K to 500 K. Determine its change in specific internal…

A:

Q: Why in which cases is the flue gas treatment is used?

A: Given Data : Treatment of flue gases

Q: The absolute pressure in the tank is found to be 1.206 bar. In the measurement of this pressure a…

A: Standard atmospheric pressure of 1.02325 bar corresponds to 76 cm Hg. Atmospheric pressure of 72 cm…

Q: For the beam shown in the figure, Determine the following unknowns where L1 = 4m, L2 = 3m, and the…

A:

Q: In an air-water vapor mixture at 30°C, the partial pressure of the water vapor is 1.7 kPa and the…

A:

Q: Q2) Water is being heated in a closed insulated pan stirred by a paddle wheel. During the process…

A: Given data: -  The heat transfer is Q = 5000 J. The work done is W = 1.5 kJ. The initial internal…

Q: Refer to Fig. 8-27 below. The weight of A is 50 lb; the weight of B is 80 lb. The coefficients of…

A:

Q: Determine the forces in members BC and CG. The forces are positive if in tension, negative if in…

A:

Q: Q.1) A thin steel wire of a uniform cross-section is bent into the shape shown. Locate the center of…

A:

Q: 8. Maximum roughness average is 0.8 microns, sampling length is 2.5 mm, and the lay is parallel to…

A: Solution: Maximum roughness = 0.8 microns The sampling length = 2.5 mm lay is parallel to the…

Q: (a) Establish the free body diagram and equation of motion in the matrix form for gear box,…

A:

Q: b) A tensile test was carried out on a mild steel test-piece having a diameter of 12mm and a gauge…

A: 2b) Given: Gauge Length (L)=88mmDiameter of the bar (D)=12mmLoad at limit of proportionality…

Q: 25,000 cfm of outdoor air is brought into an HVAC system air handling unit (AHU). The air is at 100°…

A:

Q: You have to do thermal analysis of a building near an arctic observatory, which has a footprint of…

A: Given: Dimension of footprint: 8-m x 12-m Height, h = 4-m Ambient temperature of air, T0=-15 C…

Q: What is the ideal column?

A: An ideal column is one that is perfectly straight, made of a homogeneous material, and free from…

Q: The figure below provides steady-state operating data for an ideal refrigeration the working fluid.…

A: Mass flow rate = 30.59 (lb/min) vapor compression refrigeration system with working fluid R-134a…

Q: The 420-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the…

A:

Q: In the engine oil industry, double-pipe counter-flow heat exchanger is used to cool the hot engine…

A:

Q: 2. An air-conditioning system requires air flow at the main supply duct at a rate of 180 m³/min. The…

A: