Multiple choice questions: 1- A voltages of 50Hz transformer are 1500 V on primary and 600 V on the secondary. It has 1.5 V per turn. Then the number of turns on primary and secondary are ---------- a) 20 and 8 b) 100 and 10 c) 1000 and 120 d)1000 and 400 e) none of the previous. 2-A 600/200 V single phase transformer is supplying a load of 60 A at a p.f of 0.707 lag. The no load current is 3A at 0.2 P.f. lag. Then the primary current is ---- a) 63A b) 22.56A c) 69A d)24 e) 21.55 f) none of the previous. S 3- The silicon ratio in transformer iron cannot be increased greater than 5% because of- a) the iron loss will increase b) the hysteresis loss will increase c) the eddy current loss will increase d) none of the previous 4- If V1 = 400V and the wattmeter read 800W at no load test then the value of Ro is none of the previous a)100 b)4002 c) 200 d)160002 S

Multiple choice questions: 1- A voltages of 50Hz transformer are 1500 V on primary and 600 V on the secondary. It has 1.5 V per turn. Then the number of turns on primary and secondary are ---------- a) 20 and 8 b) 100 and 10 c) 1000 and 120 d)1000 and 400 e) none of the previous. 2-A 600/200 V single phase transformer is supplying a load of 60 A at a p.f of 0.707 lag. The no load current is 3A at 0.2 P.f. lag. Then the primary current is ---- a) 63A b) 22.56A c) 69A d)24 e) 21.55 f) none of the previous. S 3- The silicon ratio in transformer iron cannot be increased greater than 5% because of- a) the iron loss will increase b) the hysteresis loss will increase c) the eddy current loss will increase d) none of the previous 4- If V1 = 400V and the wattmeter read 800W at no load test then the value of Ro is none of the previous a)100 b)4002 c) 200 d)160002 S

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

6-Writ the procedure of no load test of Single phase transformer and draw the connection diagram of this test
A 120 kVA, 1350/330 V single phase transformer has the following parameters: R1 = 0.34 Q, X1 = 0.59 0, R2 = 0.014 Q, X1 = 0.029 Q, Rc = 380 and Xm = 320 Q. The no load current is 4.7 A at a power factor of 0.36 lagging and the no load losses are 4.6 kW. For a full load and 0.9 power factor lagging with 300 V load terminal voltage, determine (a) equivalent circuit parameters referred to primary side, (b) percentage regulation and (c) full load efficiency. O:01 AM
solve with transformators topic With a ratio of turns of 10 to 1 and an input voltage of 120V and output 12 V, propose a system of transformer and turns
c) A 100 kVA, 4500/250 V, 50 Hz single-phase transformer has 100 secondary turns.Determine: i.The primary current.ii.The secondary current.iii.The number of primary turns.
What is transformer di not use chatgpt
You are a journeyman electrician working in an industrial plant. You are to install transformers that are to be connected in open-delta. Transformer A must supply its share of the three-phase load. Transformer B is to be center-tapped so it can provide power to single-phase loads as well as its share of the three-phase load. The total connected three-phase load is to be 40 kVA, and the total connected single-phase load is to be 60 kVA. The transformers are to have a capacity 115% greater than the rated load. What is the minimum kVA rating of each transformer?
Q/A single-phase transformer with a capacity of 100 kVA and a voltage of 2000/400 and the equivalent circuit elements are: As follows R1 = 0.1 02 x1 = 0.2 2 R2 = 0.25 2 X2 = 0.75 2 RO = 500 XO = 150 Q and feeds a load of 90 kVA at a voltage of 2000 volts and a power factor of 8.0 in delay. Calculate voltage and current Primary Royl ww JX eql
4. 100 kVA, 6800-240 V, 50 Hz single phase step down transformer has the following parameters: RLs-0.008Ω RHs-2.6Ω Ri-HS-500 0Ω XLS-0.015Ω XHs=5.22 Xm,HS=88002 Transformer is delivering 80% of rated load at rated voltage and 0.95 lagging power factor. Determine the following: a) The equivalent impedance of the transformer referred to primary. b) Input impedance of the combined transformer and load. c) Actual input voltage at HV side. d) Input impedance if load is disconnected. e) Exciting current at no load.
transformrs
Three single phase transformers are connected in a Delta-Wye configuration. Each transformer is rated 13kV/64kV. The transformers are connected to a 3 phase 13kV (L-L) supply and the balanced three phase load is 788KVA. What is the current magnitude in the secondary winding of each transformer? explain the steps too please
If the no load secondary voltage of a 1-phase transformer is 235 V and full load secondary voltage is 223 V, then the % regulation of the transformer is 5.38 52.69 12.00 31.63
You have a large single phase transformer with 7 tap settings (@ 0,+2,+4,+6% and -2,-4, and -6%) that lets you adjust the load voltage if necessary. The primary voltage is 4800V and the secondary voltage desired is 240V. Draw this arrangement with the 0% tap setting selected.