The 45 lb square plate shown is supported by 3 vertical wires.Determine the tension in each wire. El plato cuadrado de 45 lb mostrado es soportado por 3 cables verticales.Determina la tensión en cada cable. (Valor: 5 puntos)yZ'n5 in.C15 in.BX20 in.A20 in.

Answered: El plato cuadrado de 45 lb mostrado es…

Residential Construction Academy: House Wiring (MindTap Course List)

5th Edition

ISBN:9781337402415

Author:Gregory W Fletcher

Publisher:Gregory W Fletcher

Chapter16: Video, Voice, And Data Wiring Installation

Section: Chapter Questions

Problem 2RQ

See similar textbooks

Similar questions

Describe how an electrician can tell Type AC and Type MC cable apart. (Objective 2-5)
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
Describe the purpose of an LB conduit body used in a residential service entrance Installation that uses electrical conduit. (Objective 8-1)
Name the ampacity for the following copper conductors according to Table 310.15(B) (16): (Objective 6-4) a. 10 AWG THW amps _____ amps b. 8 AWG THWN amps_______ amps c. 1 AWG THHN amps ______ amps d. 4/0 TW amps ______ amps
Determine the smallest value of yield stress Fy, for which a W-, M-, or S-shape from Part 1 of the Manual will become slender. To which shapes does this value apply? What conclusion can you draw from your answer?
A beam is part of the framing system for the floor of an office building. The floor is subjected to both dead loads and live loads. The maximum moment caused by the service dead load is 45 ft-kips, and the maximum moment for the service live load is 63 ft-kips (these moments occur at the same location on the beam and can therefore be combined). a. If load and resistance factor design is used, determine the maximum factored bending moment (required moment strength). What is the controlling AISC load combination? b. What is the required nominal moment strength for a resistance factor of 0.90? c. If allowable strength design is used, determine the required moment strength. What is the controlling AISC lead combination? d. What is the required nominal moment strength for a safety factor of 1.67?
List the minimum trade size of Type EMT for each of the following applications. Assume the use of conductors with THHN insulation. (Objective 12-1) a. Six 14 AWG _______ b. Six 12 AWG ______ c. Three 10 AWG ______ d. Four 8 AWG _____
Why is it so difficult to process MSW?

Recommended textbooks for you

Residential Construction Academy: House Wiring (M…

Civil Engineering

ISBN:

9781337402415

Author:

Gregory W Fletcher

Publisher:

Cengage Learning

Residential Construction Academy: House Wiring (M…

Civil Engineering

ISBN:

9781285852225

Author:

Gregory W Fletcher

Publisher:

Cengage Learning

Steel Design (Activate Learning with these NEW ti…

Civil Engineering

ISBN:

9781337094740

Author:

Segui, William T.

Publisher:

Cengage Learning

Residential Construction Academy: House Wiring (M…

Civil Engineering

ISBN:

9781337402415

Author:

Gregory W Fletcher

Publisher:

Cengage Learning

Residential Construction Academy: House Wiring (M…

Civil Engineering

ISBN:

9781285852225

Author:

Gregory W Fletcher

Publisher:

Cengage Learning

Steel Design (Activate Learning with these NEW ti…

Civil Engineering

ISBN:

9781337094740

Author:

Segui, William T.

Publisher:

Cengage Learning

Materials Science And Engineering Properties

Civil Engineering

ISBN:

9781111988609

Author:

Charles Gilmore

Publisher:

Cengage Learning

Architectural Drafting and Design (MindTap Course…

Civil Engineering

ISBN:

9781285165738

Author:

Alan Jefferis, David A. Madsen, David P. Madsen

Publisher:

Cengage Learning

Construction Materials, Methods and Techniques (M…

Civil Engineering

ISBN:

9781305086272

Author:

William P. Spence, Eva Kultermann

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

El plato cuadrado de 45 lb mostrado es soportado por 3 cables verticales. Determina la tensión en cada cable. (Valor: 5 puntos) y Z' n 5 in. C 15 in. B X 20 in. A 20 in.