Eight 10-mm diameter steel bolts on a bolt circle 150 mm in radius and six 20-mm diameter bolts on a concentric bolt circle 100 mm in radius were used in a rigid coupling, If the design stress in the bolts is 60 MPa, determine the torque capacity of the coupling in kN.m

Q: The shaft ABCDE is under equilibrium. Determine the internal torque in section (3). 39.00 N-m 37.00…

A:

Q: The shaft ABCDE is under equilibrium. Determine the internal torque in section (3). 36.00 N-m 28.00…

A:

Q: A circular shaft with 50mm and its lenght is 850mm long and is made of steel, the shaft is subjected…

A: GIVEN :- diameter : d=50mm length: L=850 mm Torque subjected: T=800Nm (to determine θ we need the…

Q: The shaft ABCDE is under equilibrium. Determine the internal torque in section (3).

A: Given data, TE = Torque at E = -11 N-m (Cross-section is twisted in clockwise direction from right…

Q: In a flange coupling as shown each shaft is keyed to the both of a flange with a sunk key to…

A:

Q: For the given position of the mechanism shown in Fig. 4, determine the magnitude an direction of the…

A: according to the given details

Q: Member ABCD is a hollow circular steel shaft with a 4 inch outer diameter and a 3 inch inner…

A: Given data:- a hollow circular steel shaft outer diameter =4 inch inner diameter =3 inch  TB…

Q: Need complete solution. The given planetary gear system is composed of 3 Planetary Gears C, Ring…

A: Given: The allowable shear stress = 100 MPa The frequency of shaft A, NA = y = 20 Hz The diameter of…

Q: A truck equipped with a 50 HP engine uses a roller chain as the final drive to the rear axle. The…

A:

Q: The composite shaft below, consists of three sections, a tubular indication welded, through flanges…

A:

Q: 5. Design a compression coupling for a shaft to transmit 1300 N-m. The allowable shear stress for…

A:

Q: The marble tiling machine is designed to be powered by a 150 hp electric motor at a speed  of 1700…

A: Given:For D-120 V-belts:Working length=LD=3131.82mmpitch diameter of the smaller sheave,d=152mmPitch…

Q: The loads illustrated produce concentric axial force in the 20-mm-diameter shaft, which is made of…

A:

Q: a load ir incraasadta

A:

Q: Completely solve and box the final answer. Write legibly Determine the maximum mass (kg) can be…

A:

Q: A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the…

A:

Q: A shaft when subjected to pure torsion developed a stress of 50 Mpa. If polar moment of inertia is…

A:

Q: d3 T3 T2 T1 d1 TP. B L3 L2 L1.-

A: The polar moment inertia of a circular cross-section is defined as moment of area about the axis…

Q: 8. A nylon-core flat belt has an elastomer envelop; is 200 mm wide, and transmits 60 KW at a belt…

A: (A) Write the given data. w=200 mmP=60 kWv=25 m/sm=2 kg/mC=6 mD=300 mmd=900 mm

Q: Problem 1: Determine the internal torque in the shaft shown at A, B, and C. Show the free-body…

A:

Q: A hollow bronze shaft of 75 mm outer diameter and 50 mm meter is slipped over a solid steel shaft 50…

A: Given: The outer diameter of bronze shaft, D = 75 mm = 0.075 m The diameter of steel shaft or inner…

Q: esign a clamp coupling to transmit ‘35’ kW at ‘120’ r.p.m. The allowable shear stress for the shaft…

A: GivenPower P=35kWN=120rpmτshaft=τkey=50MPanumber of bolts n=6The permissible tensile stress for the…

Q: A truck equipped with a 50 HP engine uses a roller chain as the final drive to the rear axle. The…

A: Given: P = 50 HP N2 = 225 rpm C = 500 mm    (given unit not clear so taken as mm) Transmission…

Q: The machine is designed to be powered by a 100 HP electric motor at a speed of 1500 rpm, with…

A: Given : P = 100 HP N = 1500 rpm d = 101.6 mm D = 406.4 mm L = 123.3 inches = 3131.82 mm To find :…

Q: Member ABCD is a hollow circular steel shaft with a 4 inch outer diameter and a 3 inch inner…

A:

Q: The electric motor keeps the aluminum shaft ABCD, with rigidity modulus 27 GPa, operating at a…

A:

Q: A shaft is supported by two bearings placed 1.2 m apart. A pulley of diameter Dc meter is mounted at…

A:

Q: A torque of 10kN-m is to be carried by a flanged bolt coupling that consists of eight 10mm diameter…

A:

Q: H PROB. 8-13. -2 that of T? E PROB. 8-14. -10% C 8-14. A and B are two shafts at right angles, in…

A:

Q: A shaft is supported by two bearings placed 1.2 m apart. A pulley of diameter 425 mm is mounted at a…

A: givenDistance between bearings=1.2mDia of C=425mmradius Rc=212.5mmDC=0.65mAC=300mm≈0.3mMaximum…

Q: The shaft ABCDE is under equilibrium. Determine the internal torque in section (3). 38.00 N-m 28.00…

A:

Q: in farm equipment which requires 2200 N-m torque at 708 rpm has a diesel engine  that operates at…

A: Torque, T = 2200 N-m Speed of Diesel Engine, N1 =708 rpm  Rate of Prime Mover, N2 = 1601 rpm Number…

Q: 2200 he centre of ani the

A:

Q: supplies a torque of The motor shown in Fig. 500 N· m to shaft BCDE. The torques removed at gears C,…

A: To find the torque transmitted by transverse cross-sections in BC,CD and DE of the shaft TBC=? TCD=?…

Q: ad is increased to 16 kN

A:

Q: A spur pinion rotates at 1932 rpm and transmits to a mating gear 30 HP. The pitch diameter is 4”…

A: Given data- For spur Gear N=1932rpm Power P=30HP = 30*746=22380W (1HP=746W) Pitch diameter =4in…

Q: A shaft is supported by two bearings placed 1.2 m apart. A pulley of diameter Dc meter is mounted at…

A: First. draw the top view diagram of the two pulleys: The value of tension T1 is given as 2.25 kN.…

Q: Q: The sunwheel D has 20 teeth, the gear is 50 teeth, internal gear C is fixed. The input shaft…

A: Sun wheel Arrangement  Given Data The sun wheel teeth D , ZD=20 The sun wheel teeth C, ZC=50 Input…

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.