find the efficiency of flocculant settling if tank depth is 3 m and surface loadingof 4m/hour given the following dataTime, min.Removal percent at depth:1m0.5m1.5 m2 m2.5 m206130715855408172636157509079736763608780746870868075

Answered: efficiency of flocculant settling if…

Engineering

Civil Engineering

efficiency of flocculant settling if tank depth is 3 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Which of the following statements is false regarding the Headworks design? O Low approach velocity…

A: Given following statement regarding the Headworks design and asked to determine the false statement.…

Q: 6.8 Calculate the hydraulic detention time (0) of a CSTR with settled-solids recycle if Y = 0.6 g…

A: Solids may be organic or inorganic. For example, table salt in water would be an inorganic,…

Q: Solve,

A: Given: Effluent BOD concentration=80 ppm=80 mg/L Volume of filter, V=825 m3 Discharge, Q=50 L/sec…

Q: d) e) f), with full solution

A: d) The yield point is the point on a stress-strain curve that indicates the limit of elastic…

Q: If the efficiency of particles of diameter 0.05 mm and specific gravity 2.65 is 88%, then find the…

Q: This is an end piece for the support frame of an A-type evaporator coil. Toforce the airflow through…

A: Consider the free body diagram of the triangular end piece of for the support frame of an A-type…

Q: 10-9. A dual-media filter contains anthracite with an effective size of 1.2 mm and uniformity…

Q: Given: Rate of infiltration, in/hr 2.4 Final capacity, in/hr 0.3 Horton k, hr*1 0.1 Solve for the…

Q: The subsequent movement of infiltrated water in the unsaturated zone of a soil is called O…

Q: 18. If the overall BOD removal efficiency in 2- stage trickling filters is 65% at 20°C, what would…

A: The efficiency at any different temperature is given by: ET=E20(1.035)(T-20o) Where, T = Given…

Q: A 0.80 m deep bed of sand filter (length 4m and width 3m) is made of uniform particles (diameter =…

A: Given- Length L=4 mWidth B=3 mDischarge Q=3.6 m3/minDepth of bed D=0.8 mBed porosity n=0.4 It is…

Q: 10-7. Determine the variation in backwash velocity required to expand an anthracite medium with an…

A: Giveneffective size of particle=1 mmuniformity coefficient=1.3temperature variation=3° - 30° CTo…

Q: (ii) Briefly explain the important design considerations for aerobic composting process.

A: Note: The above questions are 2 entirely different questions not related to each other at all so it…

Q: Q3)) The reservoir has the following data: Evaporation by mass transfer = 5.5 mm/day - Emitted solar…

A: The given data is: A=Albedo=0.723 Hn=Net radiation in mm=? Hc=Radiation incoming=8.5 MJ/m2 day…

Q: A: The effluent from an industrial plant is (3.5m³/sec), has phosphorus concentration of( 850ppm)…

A: The equation is: C(x,t) = C0exp(-Ux/L) + (Q/C0*L)exp(-Ux/L)int_0^t exp(Uy/L)*exp(-(y/L)^2/4Dt) dy…

Q: 4. A settling chamber is to be 2 m wide, 7 m high, 13 m long and has 10 trays, including the bottom…

A: Given, L = 13 m B = 2 m H = 7 m n = 10

Q: Find the length of a settling chamber needed to collect 90% of 50 um particulates (pp= 1.2 g/cm).…

A: It is required to determine the settling velocity of particulates. vs=gρp-ρadp218μ Here ρp is the…

Q: Q- To obtain the lake evaporation in cm, the evaporation observed from an ISI pan under similar…

Q: Rib m. Q-6: Water flows in a confined aquifer from a fully penetrating river with a piezometric head…

Q: Ql:- Design a settling tank for a flow of 0.2 MGD if the overflow rate is not to exceed 600 gpd/n.…

A: Given data Depth Overflow rate Discharge.

Q: A monomedia filter 0.75 m deep contains sand with an effective size of 0.55 mm. The sand has a…

A: Given, Thickness of sand (L) = 0.75m Effective diameter (d) = 0.55 mm or 0.00055m To Find: Head…

Q: A rapid sand filter provided in a town have undisturbed depth of 0.55 m. The average settling…

A: Given data for the rapid sand filter:Undisturbed depth of the filter: 0.55 mAverage settling…

Q: A 3 m deep settling tank has a surface area of 900 m?. The tank is used for removing particles of…

A: Given: Depth of tank, H = 3 m Surface area, A = 900 m2 Particle size, d = 0.01 mm Specific gravity…

Q: efficiency of flocculant settling if tank depth is 3 m

A: To find the efficiency of the settling tank with depth of 3m and surface loading rate of 4m/hour.…

Q: Alum at a rate of 20 mg/l is added to an incoming discharge of 0.5 m3/s which carries 250 mg/1 of…

A: 1. Alum added at a rate of 20 mg/l.2. Incoming discharge: 0.5 m³/s3. Incoming discharge carries 250…

Q: 10 kN/m 10 kN/m 10 kN/m 10 kN/m 5 kN/m 5 kN/m 5 kN/m Il llir l V 3 m 31 2m 3 m 2 m 3 m 15 m 3m 2 m…

A: 1. To determine fixed end moments 2. Distribution Factors 3. Moment Distribution 4. Support…

Q: Assuming suitable design criteria, design a primary settling tank to treat 10000 m³/d average…

Q: 2. Use the Green-Ampt method to evaluate the infiltration rate and cumulative infiltration depth for…

A: Note:- I have calculated the values for 1 hr only, similarly the values for time up to 5 hr can be…

Q: A settling chamber is to be used to collect particles of 50 micrometers diameter and 1400 kg/m3…

A: A settling chamber is to be used to collect particles of 50 micrometers diameter and 1400 kg/m3…

Q: A rapid gravity filter operating with an influent concentration C0 of 20 mg/l suspended solids has…

Q: Q4-A) Design a Grit chamber for the following condition: 2max=4000 m³/day Qavg= 1500 m³/day,Qmin 0.3…

Q: A gravity rapid sand filter with an effective size of 0.55 ent is 1.2 designed for a water treatment…

A: The given data in the question is: The gravity rapid sand filter has an effective size of 0.55 mm…

Q: A dual media filter contains 0.4 m of sand with effective size 0.55 mm and 1.4 m of anthracite with…

A: Given, Thickness of sand = 0.4m Thickness of anthracite = 1.4m To Find: Head loss through the…

Q: e of the aquifer is 31 feet, and the elevation of the water in the canal above the base of the ifer…

Q: Given: Rate of infiltration, in/hr 3.1 Final capacity, in/hr 0.3 Horton k, hr 1 0.4 Solve for the…

Q: Surface

Q: Describe the necessity of model testing. Briefly explain Froude model laws

A: A small scale replica of the actual structure is Model. It is not necessary that models should…

Q: A concrete gravity dam is 100 ft long from upstream to downstream end. It is constructed on a…

A: Draw the following flow net for seepage occurring beneath the dam as follows: Part a.

Q: Flow velocity of water 1.25 cm/sec is observed in a continuous flow settling tank 4.5 m deep and 60…

Q: Q1)) The reservoir has the following data: Evaporation by mass transfer = 4.5 mm/day Emitted solar…

A: Given data- To find- Evaporation by Penman's equation.

Question

find the efficiency of flocculant settling if tank depth is 3 m and surface loading
of 4m/hour given the following data
Time, min.
Removal percent at depth:
1m
0.5m
1.5 m
2 m
2.5 m
20
61
30
71
58
55
40
81
72
63
61
57
50
90
79
73
67
63
60
87
80
74
68
70
86
80
75

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Settling tank has a depth of 3 m and surface area of 900 m2 is used to remove particles of size 0.01 mm and specific gravity 2.65. Compute the removal percentage of the tank for the discharge of 8000 m3/d. Take viscosity of water equal to 10-3 kg/m.s.
A single media filter has a 720mm deep bed of sand (diameter = 5 x 10^-4 m, shape factor = 0.8). The porosity of the system is 0.40. The filtration rate is 1.2 (L/s)m^2. The water viscosity is 1.14 x 10^-6 m^2/s. A. What is the Reynold’s number of the filter B. What is the friction factor for the filter? C. What is the total clean head loss across the filter in m?
How long would it take for chloride to be detected just outside the clay liner at the secondary MCL of 250mg/L? Assume diffusion is the only mechanism
Q-Surface Overflow Rate (SOR) of a primary settling tank (discrete settling) is 20000 litre/m² per day. Kinematic viscosity of water in the tank is 1.01 × 10-2 cm²/s. Specific gravity of the settling particles is 2. Acceleration due to gravity is 9.81 m/s2. The minimum diameter (in um, round off to one decimal place) of the particles that will be removed with 80% efficiency in the tank, is.
The bed thickness of a speed sand filter is 1.3 m. A sand with a specific diameter of 0.8 mm and a specific gravity of 2600 kg / m3 will be used as filter material. The shape factor of the sand is 0.9 and the porosity of the clean bed is 0.45. The water layer thickness on the bed is 1.1 m. Average filtration speed is 130 m / day and maximum filtration speed is 180 m / day. The maximum flow rate is 24087 m3 / day and the kinematic viscosity of water is 1.01x10-6 m2 / sec. The maximum head loss in the filter is required to be 1.9 m and negative pressure is not allowed. a) Find the initial head loss of the filter bed. b) Find the required number of filters and the area of each filter in case 3 filters are in reserve. c) Calculate how many meters depth the pollution penetrates at the end of filtration.
Given the earth dam and flow net shown, calculate the seepage loss under the dam if the water height behind the dam is 15ft. The soil has a hydraulic conductivity of 100 ft/year. EL 0 EL-10 Water Level 730 ft³/year O 650 ft³/year 500 ft³/year 890 ft³/year Water Level Yail=130 lb/ft³ Impervious Stratum
sluage system. (ii) The treated effluent containing grit particles from the above (i) activated sludge system is discharged into a secondary clarifier for further treatment. Assume that a spherical body undergoes settling through the clarifier with a terminal settling velocity of 2 m/s. Find the drag force on the grit particle due to the fluid. Assume that Stokes law is valid and dynamic of viscosity of effluent = 0.001 radius of spherical particle = 2 mm). In addition, outline two (2) purposes of the phi factor in particle settling? Kgm ¹s
(ii) The treated effluent containing grit particles from the above (i) activated sludge system is discharged into a secondary clarifier for further treatment. Assume that a spherical body undergoes settling through the clarifier with a terminal settling velocity of 2 m/s. Find the drag force on the body due to the fluid. Assume that Stokes law is valid and dynamic of viscosity of effluent = 0.001 Kgm-¹s-1, radius of spherical object = 2 mm)
Figure Q1(d) shows a layer of soil in a tank with upward seepage. Given the H1 = 1.5 m, H2 =2.5 m, h = 1.5 m, ysat = 18.6 kN/m³. If the hydraulic conductivity of soil, k = 0.13 cm/s; (i) Compute the upward seepage force per unit volume of soil. (ii) Determine the rate of upward seepage of water if the area of tank is 0.52 m? in m³ /min.
Please provide solution asap